Ransburg Vector AA90 79580, Руководство по обслуживанию

Страница: 33 / 88

AH-07-01.8
Vector AA90 Applicators - Installation
2 8 2 8
2 8 2 8
2 8
>
Failure to connect interlocks could result
in fire or explosion.
W A R N I N G W A R N I N G
W A R N I N G W A R N I N G
W A R N I N G
!!!!!
To install the control unit interlocks perform the
following:
1. Turn the control unit off and remove the
Turn the control unit off and remove the
Turn the control unit off and remove the Turn the control unit off and remove the Turn the control unit off and remove the
fuses. fuses. fuses. fuses. fuses.
2. Loosen the front panel screws and slide the
control unit chassis out.
3. Using a small blade screwdriver, remove the
factory installed test jumper from TB1-L2 to TB1-
L3.
4. Using a shielded cable for the interlock wiring
(supplied by user), route through the interlock
connector on the rear of the control unit and
terminate to TB1-L2 and TB1-L3 as shown in
Figure 10a. The shielded cable must have a
minimum rating of 300V and 105
°
C and its
conductors should be 0.8mm 2 (18 AWG) minimum.
Secure the cable to the interlock connector as
described in the "I/O Connectors" in this section,
so that the shield of the cable is connected to the
chassis of the enclosure.
>
Never flush the applicator while high
voltage is on.
W A R N I N G W A R N I N G W A R N I N G W A R N I N G W A R N I N G
!!!!!
RELA RELA
RELA RELA RELAY
Y
Y Y Y CONT
CONT
CONT CONT CONTACT
ACT
ACT ACT ACT
OUTPUTS OUTPUTS
OUTPUTS OUTPUTS
OUTPUTS
A set of relay contacts for high voltage (CR1) and
fault (CR2) conditions is provided at TB2-3 and
TB2-1 (see Figure 10a). One end of these relay
contacts are connected together and also
connected to a source input terminal at TB2-2
(see Figure 10c). When a source voltage is
present at TB2-2 and either the high voltage is on
or a fault condition occurs, the source voltage will
become available at the output end of the
corresponding contact. Maximum contact ratings
are as follows:
>
The interlock contacts (supplied by
user) should be rated for at least 1 amp at
240 volts AC.
N O T E N O T E
N O T E N O T E
N O T E
>
Some codes may require the interlock
wiring to be run in conduit. In this case
shielded cable is not necessary, but the
conductors used should still meet the rat-
ings specified above.
N O T E N O T E N O T E N O T E N O T E
5. Slide the chassis back in, secure the front
panel screws, and replace the fuses.
Max. Switching Capacity
Max. Operating Voltage
Max. Operating Current
MAXIMUM CONT MAXIMUM CONT MAXIMUM CONT MAXIMUM CONT MAXIMUM CONTACT ACT ACT ACT ACT RA RA RA RA RATINGS TINGS TINGS TINGS TINGS
62.5VA
125VAC
2A
A C A C A C A C A C Description Description Description Description Description
60W
125VDC
2A
D C D C
D C D C D C
When wiring to TB2, use a shielded cable and
route the wiring through the standard I/O connector
as described in the "I/O Connectors" in this section.
>
An internal 24VDC source voltage is
available at TB2-4. Using a jumper wire,
this voltage may be connected to TB2-2 to
be used as the source voltage for the relay
contact outputs. In this case, the total cur-
rent sourced should not exceed 1 amp.
N O T E N O T E
N O T E N O T E N O T E