R&S NGE-K101 страница 55 Скачать руководство пользователя

Страница: 55 / 105

Instrument Functions

R&S

NGE100B

User Manual 5601.1343.02 ─ 02

Device information

Description

Device Model

Model of the instrument, i.e. NGE102B or
NGE103B.

Serial Number

Unique identification number for the instrument.

Material Number

Instrument orderable part number.

Firmware Version

Software version that is installed in the instrument.

Calibration Date

The last registered date when calibration was car-
ried out on the instrument.

Mac Address

Mac address of the network interface.

Export OSA to USB

The Open Source Acknowledgment (OSA) of the
R&S NGE100B can be exported to USB stick for ref-
erence.

5.7.2

General Instrument Settings

General instrument settings such as keypad fallback time, screen display brightness
and buzzer setting are provided.

► Select "Device > General" menu item.

The R&S NGE100B displays the "General" dialog. See

Figure 5-25

Figure 5-25: General dialog

General Instrument Settings

www.allice.de

Allice Messtechnik GmbH

Содержание NGE-K101










































































































Результаты поиска

Содержание NGE-K101

Отзывы:

Похожие инструкции для NGE-K101

Бренды по названию

Популярные бренды

R&S NGE-K101, Руководство пользователя

Результаты поиска

Содержание NGE-K101

Отзывы:

Похожие инструкции для NGE-K101

Бренды по названию

Популярные бренды