R&S 1424.7005.02 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 514

background image

Configuration for All Measurement Types

R&S

®

NRX

64

User Manual 1178.5566.02 ─ 07

Remote command:

TRIGger<undef>:ALL:DELay[:VALue]

TRIGger<Measurement>[:CHANnel<Channel>]:DELay[:VALue]

Dropout ← Trigger Advanced

If the trigger level has been underrun with internal triggering, it is sometimes useful to
wait some time (drop-out time) before retriggering. The measurement of unwanted sig-
nal components can thus be suppressed. See

Chapter 6.3.3, "Dropout Time"

Remote command:

TRIGger<undef>:ALL:DTIMe

TRIGger<Measurement>[:CHANnel<Channel>]:DTIMe

Holdoff ← Trigger Advanced

Sets the hold-off time, see

Chapter 6.3.4, "Hold-Off Time"

Remote command:

TRIGger<undef>:ALL:HOLDoff

TRIGger<Measurement>[:CHANnel<Channel>]:HOLDoff

Hysteresis ← Trigger Advanced

Sets the hysteresis. A trigger event occurs, if the trigger level:

●

Falls below the set value on a rising slope.

●

Rises above the set value on a falling slope.

Thus, you can use this setting to eliminate the effects of noise in the signal for the edge
detector of the trigger system.

Remote command:

TRIGger<undef>:ALL:HYSTeresis

TRIGger<Measurement>[:CHANnel<Channel>]:HYSTeresis

Specific Trigger

Not available for each sensor type. Groups the specific trigger settings.

Jitter Suppression ← Specific Trigger

Defines the method how to cope with the misalignment between the trigger event and
the sample point.

"Compensate"

Compensation means resampling of trace result.

"Measure"

Does not perform resampling, but stores the measured trigger jitter.

Remote command:

TRIGger<Measurement>[:CHANnel<Channel>]:JITTer:METHod

Trigger Master State ← Specific Trigger

Enables or disables the power sensor as trigger master. If enabled, the power sensor
outputs a digital trigger signal in sync with its own trigger event. The trigger signal is
output at the port selected under

"Trigger Master Port"

Triggering

www.allice.de

Allice Messtechnik GmbH

«
...
62
63
64
65
66
...
»

Содержание 1424.7005.02



































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1424.7005.02

Power Xpert PXM 4000

Бренд: Eaton Страницы: 28

Бренд: Keithley Страницы: 32

Бренд: K-Patents Страницы: 10

Бренд: Olympus Страницы: 4

Бренд: palintest Страницы: 14

Бренд: Anritsu Страницы: 29

Бренд: VWR Страницы: 44

Бренд: Kawai Страницы: 72

Бренд: Scaletron Страницы: 63

DistanceMaster Compact

Бренд: LaserLiner Страницы: 14

Бренд: inbody Страницы: 36

Бренд: Komshine Страницы: 2

Бренд: East Tester Страницы: 36

Бренд: Kapro Страницы: 60

Бренд: ICP DAS USA Страницы: 340

ENERGY MAX EM400

Бренд: Molectron Страницы: 40

Бренд: Patlite Страницы: 21

Бренд: B&B Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды