9
LP0252BK
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Email:
•
Assemble the mini indicator by sliding one of the adaptors over the indicator wires with the boss
facing away from the indicator.
•
Thread the indicator wire through the tail tidy mount until the adaptor boss sits snugly inside the
mount.
•
Now thread a second adaptor plate over the wire and press this into the opposite side of the
indicator mount
•
Now replace the flanged nut provided with the mini indicators over the wires and begin winding
this onto the thread of the indicator – do not tighten fully
•
Slide the indicator wiring cover (item 15) over the exposed wires and slide this over the nut and
into position as shown in picture 16.
•
While holding the wiring cover back tighten the nut with a 12mm spanner until the indicator is
secure against the adaptor and replace the wiring cover as shown in picture 16 –
Do not over
tighten
•
Repeat both sides
•
Fit one length of heat shrink supplied (item 4) to protect the indicator wiring on both indicators.
•
Fit the remaining length of heat shrink supplied to cover the wires from the licence plate
illuminator.
•
Fit the license plate illuminator (item 4) to the tail tidy bracket (item 1) as shown in picture 17
•
Use your 6mm spanner to tighten the illuminator to the mounting tab as shown in picture 18
•
Align the two slots of the tail tidy support bracket (item 2) to the underside of the tail tidy
assembly as shown in image 19
•
Attach the support plate to the tail tidy bracket using two m5 bolts and nyloc nuts (items 8 and 9)
through the two rearward slots as shown in image 20.
Do not tighten these at this stage.
•
Neatly route the wire towards the front of the tail tidy securing it to the underside of the LH leg of
the bracket with the indicator wires.
•
With the tail tidy now assembled, offer the assembly up to the bike as seen in picture 23 and feed
the wire through the access hole on the left-hand side of the tail where the original wires were
routed.
•
Using
two spacers (item 18) placed into the tail mount recesses and
M6 x 20 button head bolts
(item 5) with M6 washers (item 6) carefully secure the front 2 mount holes of the tail tidy to the
motorcycle as shown in pictures 24.
Do not overtighten as this could cause damage to the plastic
underside of the motorcycle, ensure to use a locking compound when fitting these bolts and keep
the tail tidy supported during the next step
.
•
Using the remaining spacers (item 18)
and M6 x 20 (item 5) button head bolts with M6 washers
(item 6), secure the rear two tail tidy mounts ensuring the bolts pass though the support plate and
bracket.
Do not overtighten as this could cause damage to the plastic underside of the motorcycle,
ensure to use a locking compound when fitting these bolts.
•
Now with the tail tidy secure, tighten the bolts and nyloc nuts connecting the tail tidy and slotted
support bracket in their natural location.
•
Attach the wiring cover plate (item 3) on the top of the tail tidy over the two supporting nylocs
using the two M4 button head bolts (item 7) and tighten to the correct torque as shown in image 21.
•
Connect the indicator connectors to their counterparts on the OEM wiring sub-loom
•
Connect the new licence plate illuminator to the original light connectors using the chart below:
o
Licence plate illuminator BLACK to OEM WIRING GREEN/WHITE
o
Licence plate illuminator RED to OEM BROWN/YELLOW
If using OEM indicators
•
Route the indicators wires through their original connectors on the wiring sub loom, ensuring they
are connected to the correct LH/RH sides.
