R&G Racing
Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ.
Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301
www.rg-racing.com
Email:
PAGE 3 OF 9
FP0225BK
FITTING INSTRUCTIONS
•
Fit one nut (item 5) and washer (item 6) on spindle-bar (item 2), engage the nut so the plastic
insert of the nut is fully engaged, and the bar protrudes by 1 to 2 threads. It is recommended to
use a small amount of superglue or Loctite to fix this nut as this will aid when tightening the
opposite side later.
•
Feed the spindle-bar with nut and washer through either crash protector (item 1) so the washer
sits into the recess of the crash protector.
•
Pass the spindle bar through the LHS metal spacer (item 3) with the flat face sitting against the
crash protector.
•
Pass this assembly through the front wheel spindle from the left-hand side so the OEM spindle nut
fits into the LHS spacer (item 3) recess.
•
Slide the RHS spacer (item 4) over the protruding end of the spindle on the RHS of the bike so the
smaller diameter of the spacer locates into the internal diameter of the spindle.
•
Place the remaining crash protector (item 1) over the exposed end of the spindle bar on the RHS.
•
Fit the remaining washer (item 6) and Nyloc nut (item 5) from the kit onto the thread protruding
from the crash protector.
•
Tighten each nut on both sides evenly and ensure that the plastic insert of both nuts are fully
engaged and protruding threads are equal on both sides.
•
Do not overtighten
–
the Nyloc nuts will hold it tight.
•
Check the fork protectors are secure and held firmly against the spacers and do not spin.
•
After riding the bike, check the tightness of the nuts regularly (e.g. when cleaning the bike).
ISSUE 1 - 20/11/2019 (FB)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill
and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring
that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall
at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified
or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or
if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing
death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the
amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statuto
ry
rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P
–
at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
