Randell 8000D-290 Series Скачать руководство пользователя

Страница: 5 / 16

OM-8000D SERIES PREP TABLES

SERVICE

CAUTION: COMPONENT PARTS SHALL BE REPLACED WITH FACTORY OEM PARTS.

SERVICE WORK SHALL BE DONE BY FACTORY AUTHORIZED SERVICE

PERSONNEL, SO AS TO MINIMIZE THE RISK OF POSSIBLE IGNITION DUE TO

INCORRECT PARTS OR IMPROPER SERVICE.

CAUTION: BEFORE MAKING ANY REPAIRS, ENSURE THE UNIT IS DISCONNECTED

FROM ITS POWER SOURCE.

This piece of equipment uses a R290 Refrigeration system.  This equipment has
been clearly marked on the serial tag the type of refrigerant that is being used.
There is also a warning labels stating that the unit contains R290 refrigerant. R290
is safe to use as long as you follow these warning labels.
No smoking or open flames when servicing this equipment. If needed, use a CO2
or dry-powder type fire extinguisher
Replacement parts used on any R290 Refrigeration system cabinet must have
specific UL certification for non-sparking components.
Only authorized service technician, certified in R290 system should service this
equipment.

MANIFOLD SET

A R134A manifold set can be used for servicing this equipment.

REFRIGERANT RECOVERY

Follow all national and local regulations for R-290 refrigerant recovery.

LEAKING CHECKING AND REPAIR

Leak check an R-290 system the same way you would an R-134a or R-404A
system with the following exceptions.
1.  Do not use a Halid leak detector on a R290 system.
2.  Electronic leak detector must be designated specifically for combustible gas.
Use of a bubble solution or an ultrasonic leak detector are acceptable.
When repairing a leak, it is recommended using oxygen free dry nitrogen with a
trace gas not exceeding 200PSI.
When accessing an R290 system, piercing valves are not to remain on the
equipment in a permanent manner. After charge is recovered, Schrader valves
are to be installed on the process stubs. Proper charge is to be weighed into the
system and the system is to be leak checked afterwards.
The R290 equipment must have red process tubes and other devices through
which the refrigerant is serviced, such as any service port.  This color marking
must remain on the equipment. If marking is removed, it must be replace and
extend at least 2.5 centimeters (1”) from the compressor.

CHARGING

Follow the charge amount specified on the data tag. It is recommended to use the
shortest hoses possible to prevent undercharging.
•  Ensure the system is sealed and leak checked
•  Evacuate system to a minimum 500 micron
•  Weigh in correct charge
•  Leak check the system again
•  Bleed the refrigerant from the high side hose to the low side hose
•  Disconnect the hoses
•  Remove line taps

Greasy and fatty acids, blood,

burnt-on foods

Easy-Off, Degrease It,

Oven Aid

Excellent removal on all

finishes

Grease and Oil

Any good commercial

detergent

Apply with a sponge or

cloth

Restoration/Preservation

Benefit, Super Sheen

Good idea monthly

Reference: Nickel Development Institute, Diversey Lever, Savin, Ecolab, NAFEM
Proper maintenance of equipment is the ultimate necessity in preventing costly
repairs. By evaluating each unit on a regular schedule, you can often catch
and repair minor problems before they completely disable the unit and become
burdensome on your entire operation.
For more information on preventive maintenance, consult your local service
company or CFESA member. Most repair companies offer this service at very
reasonable rates to allow you the time you need to run your business along with
the peace of mind that all your equipment will last throughout its expected life.
These services often offer guarantees as well as the flexibility in scheduling or
maintenance for your convenience. For a complete listing of current Unified Brands
ASA please visit www.unifiedbrands.net.
Unified Brands believes strongly in the products it manufactures and backs those
products with one of the best warranties in the industry. We believe with the
proper maintenance and use, you will realize a profitable return on your investment
and years of satisfied service.

REPLACEMENT PARTS

To order parts, contact your Authorized Service Agent. Supply the model
designation, serial number, part description, part number, quantity, and when
applicable, voltage and phase.

CONTACT US

If you have questions pertaining to the content in this manual, contact Unified
Brands at 888-994-7636 or [email protected].

TROUBLESHOOTING

This unit is designed to operate smoothly and efficiently if properly maintained.
However, the following is a list of checks to make in the event of a problem. Wir-
ing diagrams are found at the end of this manual. When in doubt, turn unit off
and contact service at 888-994-7636 or [email protected].

SYMPTOM

POSSIBLE CAUSE

PROCEDURE

Unit does not run

No power to unit

Plug in unit

Control in OFF position

Turn controller on

Faulty control

Call for service at 888-994-
7636

Unit too cold

Incorrect set point