RANCHO RS6501, Руководство по установке, Страница: 3 / 11

PARTS LIST
P/N DESCRIPTION QTY.
130019 Rear Track Bar Bracket 1
420027 Rear Bumpstop Spacer 2
694 Coil Spring – Front 2
695 Coil Spring – Rear 2
1335 Lower Link 4
130019 Rear Track Bar Bracket 1
8597 Link Bushing kit 1
420025 Sleeve 1.0 x .219W x 2.53 8
530-4 Link Bushing 16
860160 Shift Relocation Kit 1
176090 Bracket 1
1/4-20x.75 BHCS 4
1/4 SAE Washer 4
1/4-20 Nyloc Nut 4
Thread Lock 2
860072 Rear Track Bar Relocation Kit 1
420026 Sleeve 1
7/16-14x1.0 HHCS 1
7/16-14 Stover Nut 1
7/16 SAE Washer 2
M12-1.75x70 HHCS 2
M12-1.75 Nut 2
SAE Washer 4
3/8-16x1.0 HHCS 1
3/8-16 Stover Nut 1
3/8 SAE Washer 2
860161 Skid Plate Spacer / Bumpstop Kit 1
176091 Skid Plate Spacer 6
176092 Skid Plate Shim 6
1/2 Cone Washer 6
1/2-13x2.5 FSHCS 6
M10-1.50x70 HHCS 2
10mm Lock Washer 2
860483 Skid Plate Spacer MY2003 1
M12-1.75 x 65 HHCS 6
12mm Washer 6
176088 Rear End Link 2
176609 Front End Link 2
176300 Front End Link Adaptor 2
176604 Front Brakeline Drop Bracket 2
P/N DESCRIPTION QTY.
860155 Rear End Link Hardware 1
545 End Link Bushing 4
7/16-20 x 2.5 Gr 5 HHCS 4
7/16-20 Gr 8 Stover Nut 4
7/16 Hardened SAE Washer 4
7/16 Hardened USS Washer 6
860684 Front Suspension Hardware 1
M10x1.25x35mm Gr 10.9 HHCS 2
M10x1.25 Top-lock Gr 10.9 Nut 2
M10 Hardened Washer 4
3/8-16 x x 1.5 Type F HHTS 2
545 End Link Bushing 4
420084 Sleeve .688 x .522 x 1.4 4
1/2-20 x 2.75 Gr 8 HHCS 2
1/2-20 Gr 8 Nylock Nut 2
1/2 Hardened Washer SAE 4
1/2 Hardened Washer USS 4
1/2-13 x 2.75 Gr 8 HHCS 2
1/2-13 Top-lock Gr 8 Nut 2
860516 Hardware Kit 1
8mmx1.25x20mm Gr 10.9 HHCS 2
8mmx1.25 Nylock Nut 2
M8 Hardened Washer 2
Tie Strap 6
88501 Jeep TJ Sport Kit Instructions 2
94180 Information Pack 1
780281 Rancho Decal 1
88056 Instructions 1
94119 Consumer/Warranty Information 1
94177 Warning Sticker 1
RANCHO LINK ASSEMBLY
B
USHING
& S
LEEVE
I
NSTALLATION
1) Lubricate the outside diameter of two urethane
bushings 530-4 with a silicone spray or a mild solution of
soap and water.
2) Press the lubricated bushings into one end of a new
Rancho suspension link 1335 as shown in Figure 1.
3) Lubricate the outside diameter of sleeve 420025
and the inside diameter of the installed urethane bushings
with synthetic grease. Refer to Important Note P. Press the
sleeve into the bushings.
Figure 1
NOTE: It may be necessary to use a bench vise or C-clamp
to press the bushings and sleeves into the cast links. Do not
use a hammer.
420025
530-4
1335