background image

WARRANTY

ALL  WARRANTIES  OF  THE  PRODUCTS  DESCRIBED  HEREIN,  EXPRESSED  OR 
IMPLIED,  INCLUDING  THE  WARRANTY  OF  MERCHANTABILITY  AND  FITNESS 
FOR  PARTICULAR  PURPOSES  ARE  SPECIFICALLY  EXCLUDED,  EXCEPT  FOR  THE  
FOLLOWING:  ITW  BRANDS  WILL  REPAIR  OR  REPLACE  AT  ITS  SOLE  OPTION 
ANY  TOOL  PART  OR  FASTENER  WHICH  WITHIN  90  DAYS  AFTER  SALE  BY  
ITW  BRANDS  IS  FOUND  BY  ITW  BRANDS  TO  BE  DEFECTIVE  IN  MATERIAL  OR 
WORKMANSHIP,  NORMAL  WEAR  AND  TEAR  EXCLUDED.  THIS  IS  THE  SOLE  
WARRANTY OF ITW BRANDS AND THE SOLE REMEDY AVAILABLE TO THE BUYER. 

NOTE: It is very important that the operator of this tool completely reads and under-
stands the entire tool manual and completes the Operator's Exam on the last page. 
The warranty will not be valid until the test is received, along with a copy of your 
sales receipt, and reviewed by ITW Brands. Operator's license can also be obtained 
at: www.ramset.com

TO AVOID SERIOUS INJURY OR DEATH

Operators and bystanders 

must wear eye and hearing 

protection.

Never close tool with hand over fastener loading end of the tool. 

A serious hand injury from penetration by the piston or a 

discharged fastener could result.

Read manual before 

operating tool.

WARRANTY 

Содержание HD22

















Отзывы: