background image

-- Ill. OPERATION--------------

You  can take full  advantage  of all the features  of your 

RAMROD  Mini-Skid 

by 

following  the  operating  information  presented  here.  The  Mini-Skid  has been 

designed to do a lot of work with a minimum of operating fatigue. 

PRE-STARTING INSPECTION AND PREPARATION 

Before you start the Mini-Skid for the first time each 

day, perform the following checks and service: 

1. Check engine crankcase oil level.

2. Check engine fuel and open fuel shut-off valve if 

closed.

3. Check hydraulic fluid level in tank.

4. Check  for  fuel,  engine  oil  or  hydraulic  leaks.

-WARNING-

Never check for hydraulic leaks with

your  bare  hand.  High  pressure  fluid  could

penetrate your skin and cause injury.

5. Visually inspect all hoses, lines, fittings, tires, pivot

points,  mounting  pins,  nuts  and  bolts,  safety

shields  and  decals  for  possible  failure  or

looseness.

6. Check that all controls are in the neutral position.

&

WARNING 

Do  Not  Move Any  Of  The  Control 

Levers  Unless  Standing  With Both 

Feet On The Platform And Holding The 

Grip Handles. 

STARTING PROCEDURE - GASOLINE ENGINE 

1 .  Push the throttle lever down slightly. 

2. Pull choke control completely out.

3. Turn the ignition switch to "ON" and then through

to the "START" position. (If the engine fails to start

by cranking for 10 seconds, wait 5 seconds before

trying again).

4. As the engine warms up,  push back the  choke

control gradually.

5. Set  the  throttle  lever  for  idling  speed.  Avoid

excessive engine speed during warmup.

6. To restart a warm engine - move throttle control

slightly and turn ignition key to "START".

IMPORTANT 

Ensure  Than  The Auxiliary Lever Is 

Kept Neutral When Not Being Used To 

Avoid  Wasting  Power.  Engine  Is 

Difficult  To Start If Lever Is Engaged. 

Hydraulic Oil May Also Overheat. 

IMPORTANT 

Do Not Crank Engine With Starter For 

More Than 10 Seconds At A Time, As 

This Will Overheat The Starter. 

IMPORTANT 

Do Not Put Mini-Skid Under Full Load 

Condition  Until  It  Has  Had  An 

Adequate Warm-Up Period. 

NOTE: 

For more information regarding engine starting and operation, refer to your 

Briggs and Stratton  "Owner's Manual". 

JULY  1998 

- 7 -

RAMROD TASKMASTER 

Содержание MINI SKID TASKMASTER Series






































Отзывы: