Raisecom RC801-60B-FV35 Series Скачать руководство пользователя

Страница: 2 / 30

Raisecom Technology Co., Ltd

1. Cautions

Please read the following notices carefully before installing

and using the device. Raisecom does not respond to any loss

that caused by violating safety notice.

RC801/803/805-60B-FV35 series device provides V.35

synchronization data interface which complied with ITU

standard. Please firstly connect the V.35 cable before the

device power on. It is seriously forbidden to insert or pull out

V.35 cable when the converter and the other end device are

both power on, otherwise the V.35 interface will be damaged.

This device also provides high sensitive optical interface.

Before connect this device to Fiber media converter please

test the transmitting optical power of the latter. If the optical

power is beyond the overload point of this device please don’t

connect them, otherwise the optical module will be damaged.

This RC801/803/805-60B-FV35 series fiber-optic modem also

provides E1 interface which complied with ITU-T G.703

standard. When connect it to other device please ensure that

the grounding mode of the two devices which linked by the

Содержание RC801-60B-FV35 Series































Результаты поиска

Содержание RC801-60B-FV35 Series

Отзывы:

Похожие инструкции для RC801-60B-FV35 Series

Бренды по названию

Популярные бренды

Raisecom RC801-60B-FV35 Series, Руководство пользователя

Результаты поиска

Содержание RC801-60B-FV35 Series

Отзывы:

Похожие инструкции для RC801-60B-FV35 Series

Бренды по названию

Популярные бренды