RAISE 3D N2 Скачать руководство пользователя страница 8

Страница: 8 / 8

WWW.RAISE3D.COM

AMERICA · ASIA · EUROPE

Filament Run-out Sensor Installation Guide

STEP 10: Loading

STEP 11: Attach All Removed Parts

Re-attach the components that have been removed.

This includes:



The Wire-Path Covering (Step 9)



Motion Controller Box covering (Step 8)



Back Panel and door (Step 2)

STEP 12: Attach All Removed Parts

Please download Motion Board Firmware with FRS version from

https://www.raise3d.com/pages/filament-run-out-sensor-installation-instruction

and Version 0.9.7

Touchscreen Firmware from https://www.raise3d.com/pages/download.

Save the two firmwares in USB storage. Attach the USB storage onto the screen and reboot the printer.

Continue to the “Motion Controller Firmware Update” for instructions on how to update to the motion

board firmware.

Load filament through the Run-Out Sensor and up

through the Bowden tube to make sure the filament

path is assembled correctly.

Note the filament feeding order for each nozzle to

prevent false alarm.

Содержание N2









Результаты поиска

Содержание N2

Отзывы:

Похожие инструкции для N2

Бренды по названию

Популярные бренды

RAISE 3D N2, Руководство по установке

Результаты поиска

Содержание N2

Отзывы:

Похожие инструкции для N2

Бренды по названию

Популярные бренды