background image

 

Connecting Cables 

KW 4V8

 

Warning 

Use only electrical cable with a sufficient diameter. For our technical purposes a larger diameter is always 
recommended. 

 

The diameter of the grounding cable must be at least as large as that of the positive cable. 

 

Lay the cables one by one and in succession. Pay attention to performing a professional installation. Always use 
rubber sleeves for protection when wiring through metal. Use appropriate lugs and insulation caps. 

 

Do not bend the cables at a right angle. Avoid contact with sharp metal or surfaces that could damage the 
insulation. 
 

 

Connecting Cables 

 

Warning 

Separate the clamps of the current supply from the battery before maintenance, assembly, or disassembly. In all 
cases at least the negative pole should be detached. 

 

Always install a fuse at the positive current supply cable of the battery and as near as possible to the battery clamp. 
When possible use the included fuse. 

 

Always follow the accompanying instructions when connecting an external condenser. 
 
We do not accept responsibility for damage caused by the inappropriate use of an external power supply. 

 

Connecting and Installing 

 
Warning 

Make sure that the grounding connection is sound. Attach the cable to a metal part of the vehicle from which the 
lacquer or other surface finish has been removed. 

 

Use cables of the appropriate length, keeping them as short as possible. 

 

In order for the anti-interference system to function, the RCA sockets may not come into contact with the metal 
enclosure. 

 

Packaging 

 

The amplifier is packaged in a cardboard box designed for its protection. Do not damage the packing and keep it 
for later use in case of damage. 
 
Upon receipt of the amplifier make sure that: 
 
1.) The packaging is intact, the contents correspond to the specifications, and the product is in no way damaged.   
 
2.) In the event of missing or damaged parts, please contact your dealer immediately. Refer to both the model and 
serial number, which can be found on the underneath of the amplifier. 
 
 

Содержание KW 4V8




















Отзывы: