Rain Bird ESP-SMTe Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 34

Rain Bird ESP-SMTe Скачать руководство пользователя страница 19

ESP-SMTe Controller

19

System Restore

Restore Contractor Default settings and restore original

Factory Default settings.

Turn the dial to System Restore.

Contractor Defaults

Restore settings that were saved using the Save Contractor

Defaults feature.

c

b

NOTE: Current settings are overwritten.

A

Select Contractor Defaults.

B

Press RESTORE to restore the Contractor Defaults.

C

The following screen is displayed while the controller

reconfigures.

• When the restore is complete, the display returns to the

RESTORE SETTINGS menu.

Factory Defaults

Restore the original factory default settings.

c

b

NOTE:

All current zone settings are erased. Any settings

saved using Save Contractor Defaults are NOT affected.

A

Select Factory Defaults.

B

Press RESTORE to restore the Factory Defaults.

C

The following warning is displayed; press RESTORE.

D

The following screen is displayed while the controller

reconfigures.

E

When the restore is complete, the option to switch

programming modes is displayed.

F

Select the desired programming mode and begin

programming the controller per the mode selected.

>> For Simple Smart mode, go to page 11.
>> For Advanced ET mode, go to page 21.

«
...
17
18
19
20
21
...
»

Содержание ESP-SMTe



































Отзывы:

Нет отзывов