Rail King UNION PACIFIC 4-6-2 49er Скачать руководство пользователя страница 32

Страница: 32 / 36

RailKing U.P. 49er Operating Manual

RAILKING

BATTERY PROBLEMS

REMEDY

I get no sounds when the engine shifts between the

direction states.

The battery may be dead or needs charging. See the

Battery Backup section for more information.

After I turn off my transformer, my engine continues to

make sounds before quitting with a ding of its bell.

ProtoSounds continues to sound for approximately 10

seconds after power to the track has been shut off.

The sounds distort at low voltages.

The battery is insufficiently charged or dead. Follow

the recharging instructions found in the section entitled

Self Recharging Battery Backup System.

A repeating whistle blast occurs after the power has

been shut down.

The ProtoSound module has an internal defect and

should be returned to the factory for proper repair or

replacement.

RESET PROBLEMS

REMEDY

When I first turn the power on, the engine will not

begin to run. I have to turn the throttle off and then on

again to get the engine to operate.

This is normal behavior. When power to the track is

first turned on, ProtoSounds enters a RESET phase

at which time the engine undergoes a system check.

Power must be interrupted to get the engine into the

Forward Phase. See the section entitled DCRU

Reverse Unit Operation for more information.

Whenever I interrupt the power from RESET to enter

Forward, the engine goes back into RESET instead of

Forward. I know this occurs because the bell dings

twice.

Whenever ProtoSounds enters RESET after power

has been off for more than 15 seconds, the

microprocessor initiates a system check to determine

that everything is in working order. This system check

requires 2.2 seconds to complete during which time

the engine will play the steam startup sounds. We

recommend that you dont interrupt the power in

RESET until the steam startup sounds have

completed. This will guarantee that the system check

will have been completed since the startup sounds

take longer than 2.2 seconds to play. If the problem

persists, we recommend that you operate the throttle

with a slower movement as you interrupt the power in

RESET and enter the Forwaard Phase

BRAKE SOUND PROBLEMS

REMEDY

When the transformer is throttled down, the sounds

wont play.

The brake features has not been activated. See the

section on activating the brake feature for more

information.The throttle voltage setting on the

transformer is either not starting high enough or

ending low enough to trigger the brakes sounds. Try

increasing the throttle setting to 14 volts or higher

before throttling down to 8 volts or less.

The brake sounds continue to play even after the

engine stops.

The brake feature sound record lasts for three

seconds. With practice you can control how quickly

you should stop the engine to keep it in sequence with

the sound of the brakes squeaking.

The brake feature was activated in neutral after the

engine was running in forward, but the brake sounds

would not play when triggered after the engine went

back into forward or reverse.

The brake feature will only remain enabled if it is

triggered in the first direction state you enter after

activating the feature in neutral. You cannot interrupt

the power twice to enter another direction state and

still have the brake feature active. Therefore, in order

to make the brake sound feature operate in forward,

you must first activate the feature in the neutral

position that occurs after the engine was in the reverse

state.

After triggering the brake sound and stopping the

engine in neutral, the engine begins making passenger

station sound effects.

After you trigger the brake sounds, you cannot stop

the engine in neutral and leave the track power on

without activating the passenger station sounds. If you

dont want to hear the passenger station sounds after

entering neutral, turn the power off for three seconds

to disable the passenger station sound effects.

Содержание UNION PACIFIC 4-6-2 49er





































Результаты поиска

Содержание UNION PACIFIC 4-6-2 49er

Отзывы:

Похожие инструкции для UNION PACIFIC 4-6-2 49er

Бренды по названию

Популярные бренды

Rail King UNION PACIFIC 4-6-2 49er, Руководство по эксплуатации

Результаты поиска

Содержание UNION PACIFIC 4-6-2 49er

Отзывы:

Похожие инструкции для UNION PACIFIC 4-6-2 49er

Бренды по названию

Популярные бренды