Rail King UNION PACIFIC 4-6-2 49er Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 36

background image

28

RailKing U.P. 49er Operating Manual

RAILKING

In addition to the internal gearing, it is a good idea to lubricate the leading

and trailing locomotive truck “tongues” to enhance their ability to slide on
the chassis. Follow the grease points as seen in Figure 8 on page 27.

Periodically, check the locomotive wheels and pickups for dirt buildup as

this can significantly affect the engine’s ability to perform properly. Dirty
track and dirty wheels can cause both poor electrical contact as well as poor
traction, especially on elevated track sections. Finally, dirt and oil build up
can prematurely wear out the neoprene traction tires.

TRACTION TIRE REPLACEMENT
INSTRUCTIONS

Your locomotive is equipped with two neoprene rubber traction tires on

the rear set of flanged drivers. While these tires are extremely durable and
long-lasting there may arise a time where they will need to be replaced.
Should this occur, you will need to remove the side rods from the wheels in
order to slip the new tire over the grooved drive wheel.

Before the new tire can be installed, you must make sure the old tire has

been completely removed from the groove in the drive wheel. Use a razor

blade or small flatblade screwdriver pry away any remains left from the old
tire that may still be in the drive wheel groove.

Once the old tire has been

completely removed, slip the new tire onto the wheel. You may find it
useful to use two small flatblade screwdrivers to assist you in stretching the
tire over the wheel. Be careful to avoid twisting the tire when stretching it

Rear Chassis
Mounting Screws

Front Chassis
Mounting Screws

Figure 10: Removing The Boiler From The Chassis

«
...
26
27
28
29
30
...
»

Содержание UNION PACIFIC 4-6-2 49er





































Отзывы:

Нет отзывов

Похожие инструкции для UNION PACIFIC 4-6-2 49er

Бренд: Walachia Страницы: 3

Бренд: a2pro Страницы: 11

Бренд: Kasama Страницы: 43

Ultra Flash Evo

Бренд: Carf-Models Страницы: 5

Explore Dinosaurs National Geographics KIDS

Бренд: InspirationWorks Страницы: 2

Бренд: Uberstix Страницы: 40

Бренд: marklin Страницы: 44

LittlePeople Motorized Big Top Train 77706

Бренд: Fisher-Price Страницы: 6

Бренд: Zeller Страницы: 14

USRA 0-8-0 Steam Locomotive and Tender

Бренд: Lionel Страницы: 36

Harrier GR Mk.7/9 upgrade set

Бренд: Eduard Страницы: 3

My First THOMAS AND FRIENDS RAILWAY PALS

Бренд: Fisher-Price Страницы: 4

Imagine Build Play MULTI-MOTOR 13074

Бренд: K'Nex Страницы: 72

Бренд: Fisher-Price Страницы: 28

Amazing Value Tub

Бренд: K'Nex Страницы: 28

Panzer IV Ausf. H zimmerit

Бренд: Eduard Страницы: 4

Бренд: West Michigan Park Flyers Страницы: 14

Бренд: L. G. B. Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды