Rail King 4-8-8-4 Скачать руководство пользователя страница 6

Страница: 6 / 49

PS 3.0 Enhancements

Here are some of the exciting changes incorporated into your new MTH Proto-

Sound 3.0 Locomotives. More advanced features such as Custom Speed Tables and

Advanced Consisting can be found in the DCC section of this manual.

Conventional (Analog) AC/DC Start-up/Shut-down

Your new MTH PS3.0-equipped locomotive no longer has batteries. It uses Super

Capacitors to hold the engine board alive for a short time when you shut off or

interrupt track power. Because of this, when you first apply track power to your PS3.0-

equipped O Gauge engine, you will notice the headlight comes on but nothing else.

This is perfectly normal. The capacitors are charging up during this time. The wait

time depends upon how long it’s been since you last applied power to the engine.

Typically it will take 1-15 seconds to fully charge.

NOTE: The 1-15 second charging

wait time ONLY applies to conventional AC track power.

Once the headlight shuts off, the engine will play its start-up sounds and all the lights

will come back on, simultaneously. Smoke too if you have it turned on.

The capacitors hold enough charge to play the full shut-down sounds. Also, the

capacitors allow you to operate your engine in conventional mode just like you would

any other conventionally-controlled engine. Finally, because there are no batteries, you

will notice there is no external charging jack on the engine or tender.

CAUTION:

Do not apply DCS signals and DCC signals to the same track simultaneously. The
signals are not compatible, mixing the DCS and DCC signals will damage the DCS TIU
unit.

RailKing 4-8-8-4 Big Boy Steam Engine

Activating DCC Mode

Your MTH Locomotive has a DCC Decoder installed. However, in order to activate
DCC Mode, you must install a DCS/DCC switch.

For Installation instructions, please contact MTH Electric Trains

Telephone: 410-381-2580; Fax: 410-423-0009;
[email protected],
7020 Columbia Gateway Drive, Columbia MD 21046-1532

Содержание 4-8-8-4


















































Результаты поиска

Содержание 4-8-8-4

Отзывы:

Похожие инструкции для 4-8-8-4

Бренды по названию

Популярные бренды

Rail King 4-8-8-4, Руководство оператора

Результаты поиска

Содержание 4-8-8-4

Отзывы:

Похожие инструкции для 4-8-8-4

Бренды по названию

Популярные бренды