Raider Pro RDP-SST20 SOLO, Руководство пользователя

Страница: 12 / 76

12 www.raider.bg
The level of vibrations generated is
determined according to the procedure defined
in EN 60745 and can be used for comparison
with other machines. It is also suitable for a
preliminary estimate of the vibration load. The
specified vibration level is representative of the
most common machine applications. However,
if the machine is used for other activities, with
other work tools or if it is not well maintained
as prescribed, the level of vibrations generated
may change. This could significantly increase the
cumulative vibration load in the process. For the
accurate assessment of the vibration load, the
periods in which the machine is switched off or
operated but not used is also taken into account.
This could significantly reduce the total vibration
load.
2. SPECIFIC RULES FOR SAFETY
2.1. DANGER OF INJURY! Never direct
the appliance towards yourself, other people or
animals. Be careful not to have people or animals
on the other side of the workpiece.
2.2. SAVE YOUR EYES! Wear safety glasses.
This also applies to the person helping to support
or adhere.
2.3. Charge the cartridge only when the
appliance is switched off!
2.4. Do not use the electric wire gripper.
2.5. Secure the workpiece. Fixing it is safer
with a clamping mechanism or vice than with a
hand holding it.
2.6. DANGER OF INJURY! Only use the
appliance with its staples and nails. Be careful
that brackets or nails do not protrude from the
workpiece and do not pierce it.
2.7. Short mode of operation: Allow the
appliance to cool down after 15 minutes of
operation.
2.8. Never fire staples or nails into the air.
Closed brackets or nails may cause serious
injuries.
2.9. Only connect soft materials such as
wood or fabrics to the appliance. Otherwise, the
appliance may be damaged.
3. Installation instructions
The machine comes with no battery and
charger. Only use batteries and chargers from
the R20 series
4. BEFORE USE
• CHARGER LOAD
- squeeze the filler slider 3 (see Fig. 1).
- Remove the slider 3 from the magazine 4 of
the appliance.
- Load cartridge 4 with brackets or nails.
Instructions for loading nails:
For nail loading, use the left channel as shown
in detail in Fig. 1. Note that the head of the nail
should always be up.
Note: When charging, consider the maximum
amount of about 85 clamps machines and
appliances.
1.4.6. Keep the cutting tools always well
sharpened and clean. Well-maintained cutting
tools with sharp edges have less resistance and
are easier to work with.
1.4.7. Use the machines, accessories, tools,
etc., according to the manufacturer’s instructions.
Also, keep in mind the specific working conditions
and operations you must complete. Using
the machine for applications other than those
specified by the manufacturer increases the risk
of accidents at work.
1.4.8. Information on emitted noise and
vibrations.
The noise values are determined according to
EN 60745.
Sound pressure level 73.82 dB (A);
Sound power 84.82 dB (A).
Uncertainty K = 3 dB.
Work with silencers!
The full vibration value (the vector sum in all
three directions) is determined according to EN
60745:
Value of vibrations generated:
ah = 5.16 m / s2, uncertainty K = 1.5 m / s2.
The level of vibrations generated is
determined according to the procedure defined
in EN 60745 and can be used for comparison
with other machines. It is also suitable for a
preliminary estimate of the vibration load. The
specified vibration level is representative of the
most common machine applications. However,
if the machine is used for other activities, with
other working tools or if it is not well maintained
as prescribed, the level of vibrations generated
may change. This could significantly increase the
cumulative vibration load in the process. For the
accurate assessment of vibration loadsтрябва
да бъдат взимани предвид и периодите, в
които машината е изключена или работи, но
не се uses. This could significantly reduce the
total vibration load.
2. SPECIFIC RULES FOR SAFETY
2.1. DANGER OF INJURY! Never direct
the appliance towards yourself, other people or
animals. Be careful not to have people or animals
on the other side of the workpiece.
2.2. SAVE YOUR EYES! Wear safety glasses.