manualshive.com logo in svg

Radyne OM20, Инструкция по установке и эксплуатации

Поделиться
Скачать
Radyne OM20 Скачать руководство пользователя страница 35

OM20 Universal Outdoor Modem 

OM20 Initial Configuration 

 

MN-OM20– Revision 5 

3–3 

3.2

 

Initial Configuration and Setup Process 

The following descriptions assume that the OM20 is installed in a suitable location with prime 
AC power and supporting equipment available. 
 

CAUTION

 

Before initial power up of the OM20, it is a good idea to disconnect the 
transmit output from the operating ground station equipment and terminate 
the port into a properly sized load.  This is especially true if the current 
Modulator Configuration Settings are unknown, where incorrect settings 
could disrupt the existing communications traffic.  New units from the 
factory are normally shipped in a default configuration which includes 
setting the transmit carrier off. 

 

3.2.1

 

Initial Power-Up and Configuration Verification 

Turn on the unit by connecting the power cable to J1 of the OM20 and plugging the power cord 
into the appropriate AC Mains power source.  Upon initial and subsequent power-ups, the OM20 
Microprocessor will test itself and several of its components before beginning its Main 
Monitor/Control Prog.  Upon successful completion of the powerup, the LED’s on the front of the 
unit will be Green.  If a failure is detected, the Fault LED will illuminate on the web browser 
interface and on the front Status LED. 

3.2.2

 

M&C Setup (IP Configuration & RS232 Interface) 

Connect an Ethernet cable between the unit and a computer that has web browser capability. 
Access the browser and enter the default web address for the unit.  Refer to 

Section 

6 for a 

complete description of the GUI Interface operation and parameters.  The factory set defaults for 
the Ethernet port Browser are:   
 

 

 

 

IP Address Mask: 

255.000.000.000 

 

 

 

 

Modem IP Address: 

010.000.000.001 

 

 

 

 

Server IP Address: 

010.001.001.001 

 

 

 

Router IP Address: 

010.000.001.001 

 

 
The initial field checkout of the modem can also be accomplished from the Terminal Mode.  The 
Terminal Mode has the advantage of providing full screen access to all of the modem’s 
parameters, but requires a separate terminal or computer running a Terminal Program such as 
Hyper-terminal and connection to the applicable pins on the unit M&C connector J2.  The 
recommended terminal setup is as follows (These settings can be changed via the Web Browser): 
 
 
Emulation Type: 

VT-100  

Baud Rate: 

19.2 K  

Data Bits: 

8 

Parity: 

No Parity (Fixed) 

 

Содержание OM20





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды