Radyne OM20 Скачать руководство пользователя страница 121

Страница: 121 / 220

OM20 Universal Outdoor Modem

Web Browser/Remote Protocol

MN-OM20– Revision 5

6–47

IMPORTANT

The status of the following ports may be one of the following:

Down:

The link is down.

Unresolved:

Unable to agree on connection speed.

10 Mbps Half:

Connected at 10 Base-T Half Duplex.

10 Mbps Full:

Connected at 10 Base-T Full Duplex.

100 Mbps Half:

Connected at 100 Base-T Half Duplex.

100 Mbps Full:

Connected at 100 Base-T Full Duplex.

PORT 1 STATUS

{See the note above}

Displays the current status of LAN Port 1.

PORT 2 STATUS

{See the note above}

Displays the current status of LAN Port 2.

PORT 3 STATUS

{See the note above}

Displays the current status of LAN Port 3.

PORT 4 STATUS

{See the note above}

Displays the current status of LAN Port 4.

WAN STATUS

{See the note above}

Displays the current status of the WAN Port.

Содержание OM20





























































































































































































































Результаты поиска

Содержание OM20

Отзывы:

Бренды по названию

Популярные бренды

Radyne OM20, Инструкция по установке и эксплуатации

Результаты поиска

Содержание OM20

Отзывы:

Бренды по названию

Популярные бренды