Radyne OM20 Скачать руководство пользователя страница 34

Страница: 34 / 220

OM20 Universal Outdoor Modem

OM20 Initial Configuration

MN-OM20– Revision 5

3–2

Standard OM20 Factory Default Configuration Settings

Modulator:

Data Rate:

2.048 Mbps

Mode:

Closed Network

Satellite Framing:

None

Scrambler:

V.35 (IESS)

Drop and Insert:

Disabled

Inner FEC:

1/2 Rate Viterbi

Outer FEC:

Disabled

Modulation:

QPSK

Frequency:

1350 MHz

Modulator Output Power:

-20 dBm

Demodulator:

Data Rate:

2.048 Mbps

Mode:

Closed Network

Satellite Framing:

None

Descrambler:

V.35 (IESS)

Drop and Insert:

Disabled

Inner FEC:

1/2 Rate Viterbi

Outer FEC:

Disabled

Modulation:

QPSK

Frequency:

1350 MHz

Interface:

The default will vary depending on the interface type

Ethernet:

IP Address Mask:

255.000.000.000

Modem IP Address:

010.000.000.001

Server IP Address:

010.001.001.001

Router IP Address:

010.000.001.001

IMPORTANT

IP M&C Default Reset

If the unit should lockup or lose communication during the initialization

process, the unit remote interface can be reset using the supplied reset

mating connector. By installing the connector on J2 and cycling power, the

unit communication parameters will be reset to the factory test settings.

Refer to section D for Quick Set-Up Guide

To lock up the modem with an internal loopback feature, enter ‘IF Loopback Enable’ under the
Test Menu.

Содержание OM20





























































































































































































































Результаты поиска

Содержание OM20

Отзывы:

Бренды по названию

Популярные бренды

Radyne OM20, Инструкция по установке и эксплуатации

Результаты поиска

Содержание OM20

Отзывы:

Бренды по названию

Популярные бренды