Radionics D6600 NetCom, Системное руководство

Страница: 15 / 100

D6600 NetCom
Communication System Overview
D6600 NetCom System Guide
© 2001 Radionics Page 15 46542C
8. When connecting data terminal
equipment together (i.e. D6600
COM port to PC serial port), a
null modem cable must be used.
One possible configuration for a
null modem cable is:
1
2
3
4
6
7
8
9
1
2
3
4
6
7
8
9
DTE
DB-9 Pin
DTE
DB-9 Pin
5 5
Figure 6: Null Modem Configuration
(Option 1)
When connecting data terminal
equipment to data communication
equipment (i.e. D6600 COM port to a
modem), a modem cable should be
used (i.e. straight-through cable):
1
2
3
4
5
6
7
8
8
3
2
20
7
6
4
5
DTE
DB-9 Pin
DCE
DB-25 Pin
9 22
Figure 7: Null Modem Configuration
(Option 2)
1 2 3 4 5
6 7 8 9
1 = CD (Carrier Detect)
2 = RX (Receive Data)
3 = TX (Transmit Data)
4 = DTR (Data Terminal Ready
5 = SG (Signal Ground)
6 = DSR (Data Set Ready)
7 = RTS (Request to Send)
8 = CTS (Clear to Send)
9 = RI (Ring Indicator)
Figure 8: Null Modem Pinout
Description
9. Using an appropriate (Ethernet or Token Ring) network cable, connect the 10 Base-T connector of the
D6680 Network Adapter to network drop
(This is usually a RJ-45 wall plate).
10. If a COM1 expansion package is installed in the D6600 Receiver (see next section for installation
instructions), then connect a second D6680 Network Adapter (not included) to COM1. (A D6672 COM1
Expansion Kit must be separately ordered and the D6672 must be installed. See the D6672 Installation
Sheet for details.)
COM1 is the 9-pin connector to the left of the CPU Terminator card looking at the rear of
the unit. Use a straight modem cable if connecting to Channel 1 (the 25 pin connector) of the D6680
Network Adapter. Use a NULL
modem cable if connecting to Channel 2 (the 9-pin connector) of the D6680
Network Adapter. (See Figure 6 or Figure 7 for pin outs).
11. If you are utilizing a second D6680 Network Adapter, connect the 10 BASE T connector of the second
D6680 Network Adapter to the network drop (This is usually a RJ-45 wall plate).
12. Connect a PC with an appropriate (Ethernet or Token Ring) network interface card (NIC) to the network
using a 10 Base-T Ethernet cable.
Note: This PC is connected to the network for D6200 Software applications, for configuring the D6680 Network
Adapters, and setting up any D9133TTL’s or C900TTL’s.
13. OPTIONAL: Connect a second PC with an appropriate (Ethernet or Token Ring) network interface card
(NIC) to the network using an appropriate network cable.
Note: This PC is connected to the network for Automation software applications such as the products from MAS, ABM,
BOLD, S.I.S., SIMS, etc.
14. Using the supplied 16 VAC wall plug-in transformers, apply power to the network adapter(s).
15. Turn power on to the D6600.
16. After the System is ready, use the up and down arrow keys to adjust the contrast if needed.
17. The first prompt will ask for a password. You should see:
ENTER PASSWORD: _
18. Key in the default programming password,
then press the
M / E
key.
1. EVENT DATABASE