Radio Thermostat CT32 Скачать руководство пользователя страница 12

Страница: 12 / 18

Congratulations, you have successfully

installed your unit.

Please proceed to the OPERATING Guide to

initialize the CT32.

IMPORTANT:

If you have labeled and connected your

wires and followed the correct HVAC setup, and your system

still does not operate, contact technical support.
STATEMENT OF USE: This thermostat can be used with

24VAC heating and cooling systems and also millivolt

heating. It is powered by 4AA batteries, 24VAC (C wire),

or 24VAC adapter. It cannot be used with line voltage

HVAC systems. This thermostat is digital and your

desired heat or cool temperatures can easily be set on

the large touch screen with the +/- icons. In COOL and

heat pump operation, an automatic 4 minute off-time protects the compressor from damage.

This thermostat runs on 4AA batteries. The CT32 can be externally powered with a power source rated from

12V to 24V, AC or DC, at 100ma or greater. If used, connect to the C and RH terminals (no polarity). The 24VAC

“C” wire is the other side of the 24VAC heating transformer and can be found where the other thermostat wires

connect at the wall or at the furnace. Do not use the common or ground side of the line voltage.

MODE

button

Содержание CT32


















