rada Safetherm Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 29

rada Safetherm Скачать руководство пользователя страница 14

14

1.

Slide the 'O' seal along the threaded

section of the inlet connector then

screw the inlet connector and the

deck mount plate together.

2.

Insert the inlet connectors through

the basin holes.

3.

Fit the large rubber washers and back

plates then loosely fit the back nuts.

4.

Install the hot and cold supply

pipework. Make sure that the pipe

ends align with the inlet connectors.

5.

Install the compression nuts and

olives or the flat face connectors onto

the supply pipes and connect the

supply pipes to the inlet connectors.

Confirm that the inlet connectors

are the specified distance apart

then use a suitable wrench to tighten

the back nuts.

Note!

Use the flats

provided on the inlet connectors to

hold the connectors in position while

tightening the back nuts.

6.

Turn the isolators to the

OFF

position

then turn on the water supply and

check for leaks.

Note!

The isolation

valve is located in the body of the

inlet connector. To isolate the water

supply, turn the screw slot on the

isolation valve a quarter turn.

Basin Mounting

200 mm

Inlet Connector

Olive

Compression

Nut

'O' Seal

Large Rubber

Washer

Deck Mount

Plate

'O' Seal

Deck Mount

Plate

'O' Seal

Back Plate

Back Nut

Inlet Connector

«
...
12
13
14
15
16
...
»

Содержание Safetherm






























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды