background image

 
Assembly Instructions 

 

1.

 

Carefully take your scooter out of the box. 

 

 

 

 

2.

 

Assemble the Handle Bar. ** See Photo’s on Page 6   

a.

 

Lift Handle Bar up.  Do not put any pressure on the front tire while raising the Handle 
Bar. (See Figure A) 

b.

 

Tighten the Folding Quick Release bolt by turning it clockwise.  
(See Figure B & C) 

c.

 

Push the Folding Quick Release lever down to lock the Handle Bar into place.  

d.

 

Adjust the Handle Bar Quick Release by unlatching the quick release lever; adjust 
Handle Bar to a comfortable height; secure the pin into the designated holes; and tighten 
lever. 

e.

 

Unscrew star screws and lock washers on the ‘T’ of the Handle Bar and place the Grips 
into the Handle Bar.  Line up the two holes, and then screw in the star screws and lock 
washers to secure the grips. (See Figure D)  

 

3.

 

Turn the Power Switch to the on position ON ( | ). 

 
4.

 

A green light will appear, indicating a full charge. 

Note: If the light on your scooter is yellow or red, you must charge your battery.  See 
instructions on how to charge on page 6. 

 

5.

 

Before operating your scooter check the following to make sure they are secure and intact: 

 

Tires 

Check for wear, that the bolts are securely fastened, and that they are 
in alignment.  

Throttle 

While the scooter is Off (O) apply the Throttle and release; check to 
make sure that the Throttle springs back to stop after you release it. 

Handle Bar Cables 

Check to make sure that all cables are intact and that there is not 
visual damage to the cables. 

Front Fork 

Check for visual damage; make sure that all bolts are securely 
fastened.  

 

6.

 

The most important thing to remember is to have FUN and be SAFE! 

 

 
 
 
 
 
 
 
 
 
 

 

5

Содержание ZZ Cruiser




















Отзывы: