background image

sure it does not fall over). 

7.  To prevent tripping, remove any obstacles on the site. 
8.  The operator is responsible to third persons in the work area. 
9.  Do not operate the mixer unattended. 
10. Do not let children near the mixer. 
11. 

Mixer to be only used for works given in paragraph “Use as designated“. 

12. Do not modify the machine or any of its parts. 
13. The  mixer  can  only  be  put  into  operation  with  complete  and  intact  safety 

equipment. 

14. Check the moving parts for perfect functioning, if working smoothly and if no 

parts  are  damaged.  To  provide  safe  operation  of  the  equipment,  all  parts 
must be installed properly and meet all conditions. 

15. Damaged protective equipment and parts must be professionally repaired or 

replaced by a recognized professional workshop, unless otherwise specified 
in the Operating Instructions. 

16. Defective or damaged parts of the machine to be immediately replaced. Any 

damaged or illegible safety stickers must be replaced. 

17. Original spare  parts  to  be  used  only.  Using  other  spare  parts  can result  in 

accidents/injuries  of  the  user.  The  manufacturer  will  not  be  liable  for  any 
such damage. 

18. Check regularly this machine. Check all bolts, nuts, and screws for tightness 

before each use, especially those securing guards and drive mechanisms. 
Vibration during mixing may cause these to loosen.   

19. Form  a habit  of  checking to see  that all the  adjusting  tools, shovels, hand 

towels  and  other  tools/equipment  are  removed  from  mixer  area  before 
turning it on.   

20. Replace  damaged,  missing  or  failed  parts  before  using  it.  Warning  labels 

carry  important  information.  Replace  any  missing  or  damaged  warning 
labels. 

21. The tool shall be supervised when switched off and put out of children and 

animals, in order to avoid risks.   

22. The machinery shall not be operating when it is being moved. 
23. The mixer shall be positioned on level ground. 
24. Do not to reach into the drum interior to the rotating blades. 
25. Warning - use only the original standard of insulation material for repair and 

to maintain insulation distances.   

26. Disconnect the mixer from power supply before opening the enclosure and 

do not to operate it unless the enclosure is fully closed.

 

 

 

4

Содержание RACBTE800-A

























Отзывы: