background image

 
 
 
 

 

 

 

 

Declaration of conformity 

 

BUILDER 

ZI - 32, rue Aristide Berg

è

  31270 Cugnaux - France 

Tel: +33 (0)5.34.502.502 Fax: +33 (0)5.34.502.503 

 

Declares that the machinery designated below: 

 

 

 

 

 

1

0

- CE DECLARATION OF CONFORMITY  

GASOLINE TILLER 

                  

Model: RAC139PTIL-A

Serial number: 

20210171966-20210172215

The people name holding the technical file

Mr. Olivier Patriarca 

 

Complies with the provisions of the Directive & quot; machinery & quot; 2006/42 / EC and national 

laws transposing it; 

 

Also complies with the following European directives: 

The EMC Directive 2014/30 / EU 

Emission directive (EU) 2016/1628 

The Directive on Noise Emission 2000/14 / EC + 2005/88 / EC 

Noise measurements 90 dB(A) and the guaranteed noise 93 dB(A) 

Notify Body for Noise Certificate: T

Ü

V Rheinland Luxemburg GmbH 

Also complies with European standards, with national standards and the following technical 

provisions: 

EN 709: 1997+A4 

EN ISO 14982:2009 

 

Toulouse, France   

 

Le: 

01

-0

1

-202

1

   

 

 

Philippe MARIE / PDG   

Содержание RAC139PTIL-A






















Отзывы: