background image

INSTRUCTIONS

A17™ AREA LIGHT INSTALLATION 

RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install 

and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]

A17 Slipfi tter

A17 Universal Pole

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is 
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON 
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. 

WARNING: Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside. 
WARNING: Do not use an electric generator to test LED fi xtures.
WARNING: 

Min 75°C SUPPLY CONDUCTORS.

Suitable for wet locations.

MOUNTING THE UNIVERSAL ARM 

ON THE FIXTURE

1.  Remove the 

Arm Cove

r from the 

Arm

 by loosening 

Arm 

Cover Screws

 as shown in Fig. 1.

2.  Feed wires from fi xture into 

Arm

.

3.  Line up 

Arm

 and fi xture.  Tighten screws inside the 

Arm

 and 

tighten securely to housing.

4.  Replace the 

Arm Cover

 and secure with 

Screws

 as shown in Fig. 2.

Arm

Screws

Arm Cover

Arm

FIG. 1

FIG. 2

FIG. 3

FIG. 4

Square Pole Mount

1.  Place the 

Bolster Plate

 inside the 

Pole 

as shown in Fig. 3.

2.  Remove the 

Round Pole Adaptor Plate

.

3.  Fix

 Arm

 to 

Square Pole

 with 

Bolt

.

4.  Open the 

Arm Cover

 and pull the wires into the junction box.

5.  Feed supply wires from the 

Pole

 to connect to the 

Arm

Make appropriate wire connections per NEC in an approved 

enclosure 

(Fig. 7).

6.  Use bolts to tighten to the 

Pole

.

Round Pole Mount

1. 

Place the 

Bolster Plate

 inside the 

Pole 

as shown in Fig. 3.

2. 

Fix 

Arm

 to 

Round Pole 

with 

Bolt

.

3. 

Open the 

Arm Cover

 and pull the wires into the junction box.

4. 

Feed supply wires from the 

Pole

 to connect to the 

Arm

Make appropriate wire connections per NEC in an approved 

enclosure 

(Fig. 7).

5. 

Use bolts to tighten to the 

Pole

.

Pole

Bolster Plate

Bolt

Pole

Arm

Round Pole 

 Adaptor Plate

Arm Cover

Note: See Pole Drilling Pattern Detail 

(Fig. 8)

.

Содержание A17








Отзывы: