background image

FAN WILL NOT START

1.

   Check that the electricity has been 

turned on at the circuit breaker which had 

probably been turned off during 

installation.

2.

  T

3.

Be sure ON/OFF power switch on the 

wall control is in ON position.

urn off the electricity.  Check all 

connections in the wiring of the fan at the 

ceiling and make sure it follows the 

wiring instructions outlined in this 

manual.

NOISE

Note:

 Always allow a day or two "run-in" 

time for any new fan at medium or high 

speed.  When attempting to diagnose 

noise, listen carefully from several sides 

to try and isolate the location of the noise 

(blade, upper end, motor, light kit, etc.)

1.

Tighten all screws attaching blades to 

blade arms.  Remember to tighten these 

screws at least once a year because they 

may loosen slowly over time and cause a 

clicking noise.

2.

  Turn off the power.  Loosen the 

canopy and check that the wiring and/or 

wire nut connectors are not resting against 

the canopy, possibly vibrating while the 

fan is on.

3.

   Use of a standard light rheostat or an 

unapproved fan wall control to control the 

fan speed will always cause an annoying 

"hum".  Many fan motors do not work 

quietly with solid state variable speed 

controls.

4.

   Check that the rubber gasket on the 

mounting bracket has been installed if 

called for in the installation instructions.

5.

   Check that the canopy is not touching 

the ceiling.

6.

  Check that all screws on the motor 

housing and the bottom housing are tight.

FAN TURNS, BUT DOES NOT MOVE 

MUCH AIR

1.

The fan may be running in reverse. 

Press the reverse button on transmitter to

set the fan in forward operation.

2.

  The distance from the ceiling to the 

blades may be too small.  For downrod 

fans, optimal placement would be 8-9 feet 

from the floor.

3.

   The room may contain items which 

obstruct the air flow.

4.

  The fan may be too small for the size 

of the room.

EXCESSIVE WOBBLE 

Note:

A small amount of wobble is 

considered acceptable and should not be 

considered a defect.

1.

  Make certain all blades are tightly 

attached to each blades' respective blade 

arm.

9. TROUBLESHOOTING

REPLACEMENT PARTS AVAILABLE

A full range of genuine replacement 

spare parts are available at reasonable 

cost directly form Quorum 

International.  Please call us at (817) 

626-5483.  Monday through Friday 

from 8:00 A.M. to 5:00 P.M. CST.

Содержание KRESS











Отзывы: