1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,
.
.
.
2017 QuoizelInc.
Package Contents
Please go to
for product cleaning tips. Go to the
selection.
(1) A21 Medium Base bulb 150W Maximum.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/16”
drill bit, center punch, hammer, drill and wrench.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Mounting Screw
x 3
Assembly Instruction Sheet #IS-TRE9009K
For Style TRE9009K
D
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Fixture
Body
x 1
I
E
Steel Collar
x 1
Socket Collar
x 1
G
Socket
Collar Tool
x 1
Curve
Panel
x 2
Glass Panel
x 2
Glass Shade
x 1
F
B
Lock Ball
x 2
C
Fixture Hood
x 1
H
J
STEP 1
Attach the Glass Panels, Curve
Panels and Glass Shade to Fixture Body
-
A. Insert one Glass Panel (F) into the cage of
the Fixture Body (D) first. Attach the
bottom edge of the Glass Panel (F) to slot
in one of the rest sides. And fold the Tabs
in the top edge of the cage to secure the
top edge of the Glass Panel (F). Repeat
the same process to install another Glass
Panel (F) to the opposite side of the cage.
C. Place the Glass Shade (I) and the Steel
Collar (G) over the socket as shown. By
using the Socket Collar Tool (J), thread
the Socket Collar (H) onto the socket and
hand tighten until snug to secure the
Glass Shade (I).
B. Insert one Curve Panel (E) into the cage
of the Fixture Body (D). Attach the bottom
edge of the Curve Panel (E) to slot on one
narrow side of the cage. And fold the Tabs
in the top edge of the cage to secure the
top edge of the Curve Panel (E). Repeat
the same process to install another Curve
Panel (E) to another narrow side of the
cage.
D
E
F
Socket
I
G
H
Figure 1
Slot
Tab
ReleasedDate:2017-01-05
STEP 2
-
Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter
Marking Pen
Mounting
Hole
STEP 3
M
C
E
M
H
-
arking the
enter of
ach
ounting
ole
A. Remove the light fixture. Using
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
Center Punch
Hammer
Marking
Post
Lighting
Post
Post
STEP 4
Drill Holes
-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 5 above.
1/16” bit and drill
Post
Post
Fixture
Fitter
Figure 2
Figure 3
Figure 4