background image

2

       SALSA/SALSA M

Rev.5.0

IMPORTANT: 

DO  NOT  USE  YOUR  WHEELCHAIR  UNTIL 

THIS  MANUAL  HAS  BEEN  READ  AND 

UNDERSTOOD.

User Information

Intended use power wheel chairs:

Power wheelchairs are exclusively for a user who is unable 

to walk or has limited mobility, for their own personal use 

in- and outdoor. 

When an Attendant Control Module is fitted, the Power 

Wheelchair may be operated by an assistant on behalf of 

the user.

When  a  Dual  Control  Module  is  fitted  the  Power 

Wheelchair may be operated by the user, or control may 

be switched to an assistant to operate on behalf of the 

user.

The maximum weight limit (includes both the user and any 

weight of accessories fitted to the wheelchair) is marked 

on the serial number label, which is affixed to the chassis 

of the chair. 

The chair serial number is affixed also to the front page of 

the owners manual supplied with the wheelchair.

Warranty can only be taken on if the product is used under 

the specified conditions and for the intended purposes. 

The intended lifetime of the wheelchair is 5 years. Please 

DO  NOT  use  or  fit  any  3rd  party  components  to  the 

wheelchair unless they are officially approved by Sunrise 

Medical.

Area of application

The  variety  of  fitting  variants  as  well  as  the  modular 

design  mean  that  it  can  be  used  by  those  who  cannot 

walk or have limited mobility e.g. because of:

• Paralysis

• Loss of extremity (leg amputation)

• Extremity defect deformity

• Joint contractures/joint injuries

• Strokes and brain injuries

• Neurological disabilities (e.g. MS, Parkinson…)

•  Illnesses  such  as  heart  and  circulation  deficiencies, 

disturbance  of  equilibrium  or  cachexia  as  well  as  for 

elderly  people  who  still  have  the  strength  in  the  upper 

body.

• Persons who are mentally and physically able to control 

an input device to operate the chair and its functions in a 

safe way.

When  considering  provision,  please  also  note  the  body 

size, weight including the distribution of body weight, the 

user’s physical and psychological constitution, the age of 

the user, their living conditions and their environment.

If in doubt a health care professional should be involved 

to ensure the user is not exposed to unacceptable risks.

Sunrise  Medical  is  ISO  9001  certified,  which  ensures 

quality at all stages of the development and production of 

this wheelchair. 

Sunrise Medical declares under its sole responsibility that 

this product is in conformity with the requirements of the 

directive 93/42/EEC amended by 2007/47/EEC.”

Sunrise Medical declares

 that this product fulfils the 

performance requirements for a “Crash Test” to 

ISO 7176-19.

Содержание Salsa M





















































































Отзывы: