Questtel L-RF-32mW-TX Скачать руководство пользователя страница 2

1

Foreword

Foreword

This manual applies to 1310nm AM direct modulated optical transmitter with

SNMP network management interface. It mainly describes the performance

characteristics, technical

parameters,

installation and

debugging,

common

troubleshooting, and other related content of the product. In order to ensure that the

equipment can be successfully installed and safely operated, please read this manual

carefully before installing and debugging the equipment. And the installation and

debugging should be strictly according to the specified steps on the manual to avoid

unnecessary damage to equipment or accident harm to the operator. Any questions,

please contact with us in time.

Special Tips:

Optical transmitter is professional equipment, and its installation and debugging
must be operated by special technician. Read this manual carefully before

operating to avoid damage to equipment caused by fault operation or accident

harm to the operator.

While the optical transmitter is working, there is an invisible laser beam from the
optical output adapter on the front panel. Avoiding permanent harm to the body

and eye, the optical output should not aim at the human body and human should

not look directly at the optical output with the naked eye!

Please make sure that the ground terminal of the case and power outlet has been
reliably grounding before turning on the power (Grounding resistance should be

less than 4Ω) to prevent the static damage the pump laser device and harm to

human because of case charged.

To ensure the equipment can work stable over a long time in voltage unsteady or

poor voltage wave region, it´s recommend to the customer that he equips special

AC regulated power supply, or even AC uninterrupted power supply (UPS) system

for conditional regions. In the region with large temperature variation

environment (The equipment's ideal work environment temperature is 25°C) or

bad room environment it´s recommend to the customer that he equips special

air-condition system to improve the work environment.

Optical Transmitter

 User Manual

 

 L-RF-32mW-TX

www.questtel.com

[email protected]

Содержание L-RF-32mW-TX
















Отзывы: