Quest Engineering AQ5000 Pro Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 48

background image

Chapter1: Getting Started

3

Charging the Battery Pack

If you will be using the battery pack as your power source, we
recommend fully charging it before you begin recording data.

Charging the battery pack requires a Charger/Manager (bc-7400-1
or a bc-7400-2).

To recharge the battery pack:

1. Turn the IAQ Monitor off by pressing the ON/OFF button.

2. Metrosonics offers two different chargers for the battery

pack. Follow the instructions for the charger that you
have:

bc-7400-1: Plug the bc-7400-1 AC adaptor into a 120
VAC, 50 or 60 Hz, power source. Next, plug the AC
adaptor’s cable into the dc input connector of the
Charger/Manager.

bc-7400-2: Plug the power cord into a power source with
the voltage between 100 and 240 VAC, 50 or 60 Hz, and
then plug the other end of the power cord into the AC
Adaptor. Next, plug the AC adaptor’s cable into the dc
input connector of the Charger/Manager.

3. Plug the 5-pin connector of the Charger/Manager into the

battery charger input on the top end-cap of the IAQ
Monitor (see the IAQ Monitor instrument diagram at the
beginning of Chapter 3 to locate the 5-pin connector). A
few seconds later, the LED on the Charger/Manager will
turn red, indicating a high rate charging condition.

4. A fully discharged battery pack will take at least 3 hours

to completely recharge. Less discharged packs will
recharge sooner. Upon completion of the high rate
charge, the Charger/Manager's LED will turn green.
Leave the Charger/Manager connected for 30 minutes
after the LED turns green and the battery pack will be
completely recharged.

5. You can now disconnect the AC charger from the IAQ

Monitor.

NOTE:

While recharging the battery pack, the LED on the

Charger/Manager will indicate problems as follows:

«
...
6
7
8
9
10
...
»

Содержание AQ5000 Pro

















































Отзывы:

Нет отзывов

Похожие инструкции для AQ5000 Pro

Бренд: IBM Страницы: 35

ThinkVision L180p

Бренд: IBM Страницы: 28

Бренд: IBM Страницы: 23

Бренд: IBM Страницы: 4

Бренд: IBM Страницы: 30

13.3 inch HDMI LCD (H)

Бренд: Waveshare Страницы: 12

Бренд: Samsung Страницы: 111

Intelli sense 7300REL

Бренд: ReliOn Страницы: 88

Бренд: Daewoo Страницы: 75

Бренд: EDI Страницы: 16

Бренд: TANDBERG Страницы: 11

Бренд: Aaeon Страницы: 47

Two -Way Intercom Monitor

Бренд: Safety 1st Страницы: 5

IS-UM17 B Series

Бренд: Hope Industrial Systems Страницы: 24

Large Matrix Galaxy GT6X Series

Бренд: Daktronics Страницы: 33

Бренд: Eizo Страницы: 2

Бренд: Beurer medical Страницы: 120

Бренд: Logic Controls Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды