Quest Engineering AQ5000 Pro Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 48

background image

Chapter 3 Detailed Operating Instructions

16

NOTE:

The Main Screen is always displayed, even if you are not

recording on one or more of these channels.

2. Press the ON/OFF button again. The IAQ Monitor will responds

with the following:

Press RECORD

To Turn Off

ON/OFF to Continue

3. Press the Record button to turn the unit off. This is done to

prevent accidental turn off of the unit.

IMPORTANT:

The IAQ Monitor cannot be turned off while it is

recording. If you press the On/Off button while recording is in
progress, the following message will be displayed:

Cannot Turn Off

While Recording

This is done to prevent you from accidentally interrupting a test.
See "Start and Stop Recording" later in this chapter for details.

If you have not yet used Quest Suite Professional to program the
IAQ Monitor, you will see the following message when the IAQ
Monitor is turned on:

Time And Date

Not Programmed

This indicates that the real time clock has not been set with the
correct time, and all data recorded will be incorrectly time stamped.

The current date and time is automatically set from your computer's
clock when programming the IAQ Monitor with Quest Suite
Professional. See the on-line help in Quest Suite Professional for
more details.

«
...
19
20
21
22
23
...
»

Содержание AQ5000 Pro

















































Отзывы:

Нет отзывов

Похожие инструкции для AQ5000 Pro

Бренд: Targa Страницы: 22

Бренд: Paradyne Страницы: 281

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 4

Бренд: Zenith Страницы: 36

Бренд: Zenith Страницы: 36

Бренд: Zenith Страницы: 56

Бренд: Ohmeda Страницы: 70

SyncMaster 204Ts

Бренд: Samsung Страницы: 76

Бренд: Unicont SPb Страницы: 13

Бренд: Farenheit Страницы: 19

Бренд: Feelworld Страницы: 10

Бренд: Microtek Страницы: 17

Бренд: IMAGE SYSTEMS Страницы: 39

Бренд: Luvion Страницы: 58

Бренд: Daewoo Страницы: 36

Бренд: Matko Страницы: 18

Бренд: Eneo Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды