Quectel QuecOpen AG521R-NA Скачать руководство пользователя страница 66

Страница: 66 / 93

Automotive Module Series

AG521R-NA QuecOpen

Hardware Design

AG521R-NA_QuecOpen_Hardware_Design 65 / 92

The following principles of PCIe interface design should be complied with, so as to meet PCIe Gen2 specifications.

⚫

It is important to route the PCIe signal traces as differential pairs with ground surrounded. And the differential
impedance is 95 Ω ±10%.

⚫

For PCIe signal traces, the maximum length of each differential data pair (TX/RX/REFCLK) is recommended

to be less than 270 mm, and each differential data pair matching should be less than 0.7 mm (5 ps).

⚫

Spacing data lane-to-lane (intra-interface) is three times of line width.

⚫

Spacing to all other signals (inter-interface) is four times of line width.

⚫

Do not route signal traces under crystals, oscillators, magnetic devices or RF signal traces. It is

important to route the PCIe differential traces in inner-layer with ground shielding on not only upper

and lower layers but also right and left sides.

3.17.

ADC Interfaces

The module provides three analog-to-digital converter (ADC) interfaces. The voltage value on ADC pins can be

read via

AT+QADC=<port>

command, through specifying

<port>

as 0, 1 or 2. For more details about the AT

command, see

document [3]

⚫

AT+QADC=0

: read the voltage value on ADC0

⚫

AT+QADC=1

: read the voltage value on ADC1

In order to improve the accuracy of ADC, the traces of ADC interfaces should be surrounded by ground.

Table 24: Pin Definition of ADC Interfaces

Pin Name

Pin No.

Description

ADC1

245

General purpose ADC interface

ADC0

247

General purpose ADC interface

Table 25: Characteristic of ADC Interface

Parameter

Min.

Typ.

Max.

Unit

ADC0 Voltage Range

1.875

ADC1 Voltage Range

1.875

ADC Resolution

bits

Содержание QuecOpen AG521R-NA






























































































Результаты поиска

Содержание QuecOpen AG521R-NA

Отзывы:

Похожие инструкции для QuecOpen AG521R-NA

Бренды по названию

Популярные бренды

Quectel QuecOpen AG521R-NA, Проектирование аппаратного обеспечения

Результаты поиска

Содержание QuecOpen AG521R-NA

Отзывы:

Похожие инструкции для QuecOpen AG521R-NA

Бренды по названию

Популярные бренды