QUATRO
Air Technologies Inc.
------------------------------------------------------------
We Make Clean Air
----------------------------------------------------------
30 Hymus Boulevard, Montreal, Quebec, H9R 1C9 Tel.: (514) 630-4444 Fax: (514) 630-4454 website:
www.QUATRO-air.com
1- INTRODUCTION
You are now the owner of a
QUATRO SPH Or AF System
, an advanced effective indoor dust and fume collection system
designed specifically to remove particulate matter and odor causing gas phase contaminants at the source. You can expect a
noticeable improvement in air quality as the
SPH Or AF System
begins the process of reducing microscopic airborne
particulate.
The
SPH or AF System
normally features 3 Or 4 stages of filtration:
1) An OPTIONAL Pre Filter Pad OR Knock Out Pad. This captures large debris.
2) A Pre Filter for larger particles.
3) A HEPA filter captures & holds fine particles protecting the motor and ensuring a clean output.
4) A Chemical Filter to absorb & contain odor causing gas phase contaminants.
The filter sequence can be customized to your application. Contact Quatro Air for more info.
WARNING –
To reduce the risk of damage to your system read and follow all instructions. Failure to follow these
guidelines may result in undesired operation or damage that will not be covered under warranty.
2- WHAT’S IN THE BOX
The SPH model comes with the “Laser Blue” Gel filter seal. The AF model comes with a gasket seal.
Models Name
Accessories
835
835L
82B5
SPH Or AF800 230V c/w “Quick Change” Motors
SPH Or AF800 230V c/w “Long Life” Motors
SPH Or AF400 230V c/w “Brushless” Motors
(1) O&M Manual
(1) Power Cord
(2) Clamps Per Inlet (No Clamps For 1.5”)
(1) Piece Of The Appropriate Size Hose (Per Inlet)
(1) Remote Cable (AE427) Only For Units Equipped With
DB9 Remote Connector
(2) Locking HD Casters
(2) HD Casters
3- IMPORTANT SAFETY & INSTALLATION PRECAUTIONS
- Ensure to use proper voltage as indicated on the system.
- To reduce the risk of electric shock, do not expose to excessive moisture, water or rain.
- Use only on a grounded electrical circuit.
- Do not install or operate the system in an enclosed space or against a wall. Unit may overheat & shut down.
- Keep all objects at least 6” away from the casing, especially the discharge grill.
- All filters must be in place whenever this machine is in operation.
- ALWAYS turn system on/off switch to off and disconnect power prior to accessing unit, replacing filters, or servicing motor(s).
- Allow the unit to cool for 45 minutes before performing any service to the motor(s).
- Do not kink hose or restrict airflow in any way.
SAVE THESE INSTRUCTION FOR FUTURE REFERENCE
Failure to follow these guidelines may result in undesired operation or damage, not covered under this warranty.
4- INSTALLATION
1) Install the Casters on the bottom, following the instructions included with them, and then Install the unit in the chosen
location for it.
2) Open the filter access door & lid and install the filters in the correct order. See the “Filter Service & Replacement”
section for more info.
3) Connect the supplied hose from the Quatro System to the Laser/Printer.
4) Connect the power cord to the unit and then to the power source.
VERIFY VOLTAGE BEFORE CONNECTING.
- ONLY USE THE POWER CORD SUPPLIED WITH THE EQUIPMENT.
- Always plug the unit directly into the wall outlet. Do not use extension cords or power bars.
- Ideally the unit should be plugged into it’s own dedicated circuit.
- The system is designed to be constantly powered (plugged in). The system will not function correctly and may get
damaged if power source is used to control the operation. See “Controls” for more info.
5) Turn unit on & adjust the desired airflow using the arrow up and down keys. Set airflow to lowest acceptable level to
properly evacuate your equipment.
For information about remote operation see the “Controls” section.
