background image

Airborne Enterprise Module Databook

 

 

Quatech, Inc. 

100-8080-120 

7/15/2010 

27 

8.0  Antenna 

The unit supports antenna connection through a single Hirose U.FL connector, located on 
the top surface of the radio next to the RF shielding.  

Any antenna used with the system must be designed for operation within the 2.4GHz  
ISM band and specifically must support the 2.412GHz to 2.482GHz for 802.11b/g 
operation. They are required to have a VSWR of 2:1 maximum referenced to a 50

 

system impedance. 

8.1 

Antenna Selection 

The Airborne radio supports a number of antenna options, all of which require 
connection to the U.FL connectors on the radio. Ultimately the antenna option 
selected will be determined by a number of factors, these include consideration 
of the application, mechanical construction and desired performance. Since the 
number of possible combinations is endless we will review some of the more 
common solutions in this section. If your application is not covered during this 
discussion please contact Technical Support for more specific answers. 

The available antenna connections include: 

 

Host board mounted antenna 

 

Host Chassis mounted antenna 

 

Embedded antenna 

In addition to the above options, location and performance need to be 
considered, the following sections discuss these items. 

8.2 

Host Board Mounted Antenna 

Host board mounted requires that an antenna connection is physically mounted 
to the host system board. It also requires that the host board include a U.FL 
connector (two (2) if diversity is being used) to allow a U.FL to U.FL coaxial lead 
to connect from the radio to the host board. It will then require 50

 matched PCB 

traces to be routed from the U.FL connector to the antenna mount. 

There are several sources for the U.FL to U.FL coaxial cable these include 
Hirose, Sunridge and IPEX. Please contact Quatech for further part numbers and 
supply assistance. 

This approach can simplify assembly but does require that the host system 
configuration can accommodate an antenna location that is determined by the 
host PCB. There are also limitations on the ability to seal the enclosure when 
using this approach. 

This approach also restricts the selection of available antenna.  When using this 
approach, antennas that screw or press fit to the PCB mount connector must be 
used. There are many options for the antenna connector type, however if you 
wish to utilize the FCC/IOC modular approval the connector choice must comply 

Содержание 802.11B/G









































Отзывы: