Quasonix Compact RDMS Скачать руководство пользователя страница 33

Страница: 33 / 64

Compact RDMS

Telemetry Receiver

Quasonix, Inc.

Mnemonic

Name

Description

Option (s)

Required

Basic or

Advanced

Command

Mode

Restriction

*VF

Viterbi Forget
Factor

Report or set the Viterbi
forget factor, on a scale from
0.01 – 0.99

Examples:

VF Report the Viterbi
forget factor

VF 0.04 Set the Viterbi
forget factor to 0.04

VF 0.62 Set the Viterbi
forget factor to 0.62

Standard

Advanced
Command

PCM/FM

Verbosity
Level

Report or set verbosity level,
on a scale of 0 – 9

Examples:

VL Report the verbosity
level

VL 0 Set the verbosity level
to 0

VL 5 Set the verbosity level
to 5

Standard

Advanced
Command

None

ZZ Show

Options

Displays the current
hardware configuration and
options on the receiver

Standard

Advanced
Command

None

*Note regarding VF command:

The VF command sets the observation window for the Viterbi decoder in the

trellis demod. The longer the window, the more coding gain. The smaller the window, the more resistant to phase
noise. Quasonix recommends NOT manually changing this value. The Phase Noise Compensation mode
automatically adjusts this as needed.

Содержание Compact RDMS

































































Результаты поиска

Содержание Compact RDMS

Отзывы:

Quasonix Compact RDMS, Инструкция по установке и эксплуатации, Страница: 33 / 64

Результаты поиска

Содержание Compact RDMS

Отзывы: