Quasonix Compact RDMS Скачать руководство пользователя страница 29

Страница: 29 / 64

Compact RDMS

Telemetry Receiver

Quasonix, Inc.

Mnemonic

Name

Description

Option (s)

Required

Basic or

Advanced

Command

Mode

Restriction

Input Power
Level

Reports or sets the current
input power level setting

Examples:

Report the current

input power level information
tracking state

PL 0

Set the current

power level information
tracking display to OFF

PL 1

Set the current

power level information
tracking display to ON

PL reports the Input signal
level of the receiver, the
signal level into the demod,
the digitally scaled signal
level, the SNR, and eb/N0

Standard

Advanced
Command

None

Phase Noise
Compensation

Report or set phase noise
compensation state

Examples:

PN Report the phase
noise compensation state

PN 0 Set phase noise
compensation to OFF

PN 1 Set phase noise
compensation to ON

Standard Basic

PCM/FM

Reset
Defaults for
Currently
Selected
Mode

Restores factory default
parameters for the currently
selected mode on the unit

Refer to Appendix E for a list
of factory default values by
mode

Standard

Advanced
Command

None

Query
Temperature

Report the temperature in
degrees Celsius

Standard Basic

None

Содержание Compact RDMS

































































Результаты поиска

Содержание Compact RDMS

Отзывы:

Quasonix Compact RDMS, Инструкция по установке и эксплуатации, Страница: 29 / 64

Результаты поиска

Содержание Compact RDMS

Отзывы: