background image

Quantum Scalar 50 Tape Drive Removal and Replacement Instructions

Document 81-81770-01 A01

June 2007

Turning Off Drive Power

5

Figure 2  Drive Operations 
Screen

3

Use the up and down arrows to select the tape drive to be replaced and 

press 

Enter

.

4

User the up and down arrows to select 

pwr off 

and press 

Enter

.

The tape drive powers down.

Turning Off Drive 
Power Using the GUI

0

To turn off drive power using the remote management GUI:

1

On the host computer, open the internet browser software.

2

In the 

Address

 field, type http://IPaddress/where IP address is the IP 

address for the Quantum Scalar 50 library.

3

Enter the username and password and click 

OK

.

The 

Overview

 page displays (see 

figure 3

):

Note:

For dual half-height tape drive canisters, repeat the tape drive 

power off process for both tape drives in the canister. If you do 

not power down both drives before removing the tape drive 

canister, operations in progress can be interrupted causing a 

backup job to fail and/or leave a tape cartridge in one of the 

tape drives.

Note:

Refer to OCP 

Home

 screen for the library IP address.

Note:

The default username and password is 

admin

. If the username 

and password have been changed, check with the network 

administrator for the library username and password.

Содержание Scalar 50













Отзывы: