background image

Quantum Scalar 50 Tape Drive Removal and Replacement Instructions
Document 81-81770-01 A01
June 2007

4

Turning Off Drive Power

3

Remove the foam from the wrapped tape drive.

4

Remove the tape drive from the antistatic bag.

Turning Off Drive Power

0

There are two ways to turn of the tape drive power, using the operator control 

panel (OCP) or using the remote management GUI. Refer to the following 

sections:

Turning Off Drive Power Using the OCP

Turning Off Drive Power Using the GUI

Turning Off Drive 
Power Using the OCP

0

To turn off tape drive power using the OCP:

1

Press 

Ops

 from the OCP 

Home

 screen. The OCP displays the 

Operations

 

screen (see 

figure 1

):

Figure 1  Operations 
Screen

2

From the 

Ops

 screen, use the up and down arrows to highlight 

Drive 

Operations

 and press 

Enter

.

The 

Drive Operations

 screen displays (see 

figure 2

):

Note:

For dual half-height tape drive canisters, both tape drives must be 

powered down before removing the tape drive canister.

Caution:

Ensure that all tape cartridges are removed from the tape 

drives prior to powering down the tape drive. For dual half-

height drive canisters, ensure that tape cartridges have been 

removed from BOTH tape drives before powering down the 

tape drive.

Exit

Содержание Scalar 50













Отзывы: