Quantum ATL StackLink Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 28

Quantum ATL StackLink Скачать руководство пользователя страница 9

Quantum|ATL StackLink™ Installation Instructions

Document 6421009-03, Ver. 3, Rel. 0

November 2001

Installing the Bottom Mounting Tray Assembly

9

5

Secure the top mounting tray assembly to the rack, using eight

screws (YS41803) and washers (YS40404) provided in the

StackLink kit (see

).

6

Fully tighten the six screws and washers securing the rear support

arms to the sides of the top mounting tray.

Installing the Bottom Mounting Tray Assembly

0

To install the bottom mounting tray assembly in the rack:

1

Remove the six screws and washers securing the rear support arms

to the sides of the bottom mounting tray (see

Figure 5 Adjusting the
Depth of the Bottom
Mounting Tray Assembly

2

Adjust the position of the rear support arms on the bottom

mounting tray until the distance between the front and rear flanges

is approximately the same as the distance between the front and

rear mounting strips in the rack.

Note:

If the rack has widely spaced mounting holes, it may not

be possible to use all four screws to secure the rear

flanges. If this is the case, one screw per side at the rear is

acceptable.

«
...
7
8
9
10
11
...
»

Содержание ATL StackLink





























Отзывы:

Нет отзывов