manualshive.com logo in svg

Quantum ATL StackLink, Руководство по установке, Страница: 26 / 28

Поделиться
Скачать
Quantum ATL StackLink Скачать руководство пользователя страница 26

Quantum|ATL StackLink™ Installation Instructions
Document 6421009-03, Ver. 3, Rel. 0
November 2001

26

Completing the Installation

Configuring the 
Library

0

Library configuration works somewhat differently in an M1500 stack 

than it does in a single library module.

SCSI Import/Export Elements

0

To configure SCSI import/export elements using the 

Import/Export

 

option, you must use the GUI on the GUI master. See the 

Quantum|ATL M1500 Library User’s Guide

 (PN 6421000) for more 

information about this option.

Tape Drive SCSI IDs

0

To set tape drive SCSI IDs, use the GUI on the library module that 

contains the tape drives you wish to affect. For example, the addresses 

of tape drives installed in library level 2 should be set from the GUI on 

library level 2.

Library SCSI Settings

0

The SCSI host can be connected to any of the library modules. The 

SCSI settings for the M1500 stack (SCSI ID, emulation mode, etc.) are 

determined by the settings of the library module that is connected to 

the host (the SCSI master).
If you change the SCSI settings from the defaults, it is recommended 

that you change all library modules to the same settings.

Note:

The library must be power cycled before any configuration 

changes will take effect.

Note:

The GUI master is the library module that is connected to the 

StackLink motor (see 

figure 16

 on page 20).

Caution:

Although the 

Import/Export

 option appears on the GUIs 

of all of the library modules, it is only functional on the 

GUI master.

Содержание ATL StackLink





























Отзывы:

Нет отзывов