background image

RA0038LS

11.

!

WARNING!

 Incorrect sparkplug installation can result 

in serious engine damage.

!

WARNING!

 Do not cut with a dull, cracked or 

damaged metal blade. Before cutting growth, inspect 

for obstructions such as rocks, metal stakes or strands 

of wire from fences. If an obstruction cannot be 

removed, mark its location so that you can avoid it with 

the blade. Wires can catch on the blade head and be 

thrown in the air.

!

WARNING!

 Do not touch these types of objects with 

the blade.

!

WARNING!

 Before performing any maintenance on 

this machine, stop the engine and disconnect the 

sparkplug.

To Start a Flooded Engine

1.  Disconnect the spark plug boot and use the spark plug 

wrench supplied to remove the plug in a counter-

clockwise direction.

2.  If the spark plug is fouled or is soaked with fuel, clean or 

replace the plug as required.

3.  Turn the product so that the spark plug hole is aimed at 

the ground.

4.  Clear excess fuel from the combustion chamber by 

cranking the engine several times while the spark plug is 

removed.

5.  Install the spark plug and firmly tighten it with the spark 

plug wrench supplied. DO NOT OVERTIGHTEN.

6.  Reconnect the spark plug boot. Incorrect spark plug 

installation can result in serious engine damage.

Stopping the Engine

1.  Cool the engine by allowing it to run at idle for 2-3 

minutes.

2.  Slide the ON/OFF switch to the OFF position.

OPERATING THE MULTI-TOOL

Follow these steps to operate the multi-tool:
1. Remove blade guard from the blade.
2. Start the multi-tool.
3. Hold the multi-tool at waist level with your right hand (arm 

extended) on the trigger handle and your left hand on the 

front handle.

4. Place the product on the right side 

  of your body with the engine

  behind and away from your body.
5. Brushcut weeds and vines in a 

  right-to-left motion with the blade

  parallel to the ground. 

Refer to pages 7 and 8 for more 

information.

Suitable care & maintenance is essential for effective and 

trouble free operation of your Qualcut RA0038LS Multi-tool. 

Failure caused by lack of, or incorrect, care and maintenance 

is not covered under warranty. Some basic tips are outlined in 

the following section. It is recommended that unless the 

operator is experienced and skilled in the maintenance and 

repair of outdoor power equipment, maintenance and servic-

ing is carried out by an authorised Qualcut Service Agent.

Service Agents also have access to the full range of genuine 

parts and accessories available for the product. Please 

contact the Euroquip support office for details of your nearest 

service agent.

MAINTENANCE

Before Each Use:

•   Inspect the engine, tank and hoses for possible fuel  

  leaks and repair as necessary.
•   Inspect the engine cooling fins for accumulation of  

  debris and clean as necessary.
•   Inspect the entire machine for damage, loose and  

  missing components or fasteners and repair as  

 necessary.
•   Check engine oil level and top up if necessary.

Содержание RA0038LS





















Отзывы: