background image

April 30, 2015   

 

 

           7046-191C  

 

 

 

         

                  7

27I-ACC

Model:

2700-I (ACC) Insert

Laboratory:

OMNI Test Laboratories, Inc.

Report No:

061-S-78-6.2

Type:

Solid Fuel Type, Listed Room Heater

Standard:

UL1482-1996 (RR2006) and ULC 
S628-93 and (UM) 84-HUD, Mobile 
Home Approved.

The Quadra-Fire 2700 Series Wood Insert (ACC) meets the 
U.S. Environmental Protection Agency’s crib wood emission  
limits for wood heaters sold after May 15, 2015. 

This wood heater needs periodic inspection and repair for 
proper operation. It is against federal regulations to operate 
this wood heater in a manner inconsistent with operating 
instructions in this manual.

•  Installation and use of any damaged appliance. 
• Modi

fi

 cation of the appliance.

•  Installation other than as instructed by Hearth & Home 

Technologies.

•  Installation and/or use of any component part not approved by 

Hearth & Home Technologies.

•  Operating appliance without fully assembling all components.
•  Operating appliance without legs attached (if supplied with unit).
•  Do NOT Over

fi

 re - If appliance or chimney connector glows, 

you are over

fi

 ring.

Any such action that may cause a 

fi

 re hazard.

Listing and Code Approvals

A.  Insert Certifi cation

NOTE:  Hearth & Home Technologies, manufacturer of 
this appliance, reserves the right to alter its products, their 
speci

fi

 cations and/or price without notice.

NOTE:  This installation must conform with local codes. In the 
absence of local codes you must comply with the UL1482, (UM) 
84-HUD and NPFA211 in the U.S.A. and the ULC S628-93 and 
CAN/CSA-B365 Installation Codes in Canada.

C.  Mobile Home Approved 

 • 

This appliance is approved for mobile home installa-
tions when not installed in a sleeping room and when 
an outside combustion air inlet is provided.

 • 

The structural integrity of the mobile home 

fl

 oor, ceil-

ing, and walls must be maintained. 

 • 

The appliance must be properly grounded to the frame 
of the mobile home with #8 copper ground wire, and 

chimney must be listed to UL103 HT or a listed UL-
1777 full length six inch (152mm) diameter liner must 
be used. 

 • 

Outside Air Kit, part OAK-ACC must be installed in a 
mobile home installation.

Improper installation, adjustment, alteration, service or 
maintenance can cause injury or property damage. 
For assistance or additional information, consult a quali

fi

 ed 

installer, service agency or your dealer.

Quadra-Fire is a registered trademark of Hearth & Home 
Technologies.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any 
responsibility for, and the warranty will be 
voided by, the following actions: 

B.  BTU & Effi ciency Specifi cations

D.  Glass Specifi cations

This stove is equipped with 5mm ceramic glass.  Replace 
glass only with 5mm ceramic glass.  Please contact your 
dealer for replacement glass.

EPA Certi

fi

 cation #: 760

EPA Certi

fi

 ed Emissions: 3.5 grams per hour

*LHV Tested Ef

fi

 ciency: 78.8 %

**HHV Tested Ef

fi

 ciency: 72.8 %

***EPA BTU Output: 10,600 to 16,600 / hr.

****Peak BTU/Hour Output: 38,600

Vent Size: 6 inches

Firebox Size: 1.85 cubic feet

Maximum Wood Length: 18 inches

Ideal Wood Length: 16 inches

Fuel Seasoned Cord Wood

* Weighted average LHV ef

fi

 ciency using Douglas Fir dimension-

al lumber and data collected during EPA emissions test.

**

Weighted average HHV ef

fi

 ciency using Douglas Fir dimen-

sional lumber and data collected during EPA emissions test.

***

A range of BTU outputs based on EPA Default Ef

fi

 ciency and 

the burn rates from the low and high EPA tests, using Douglas 
Fir dimensional lumber.

****

A peak BTU out of the unit calculated using the maximum 

fi

 rst 

hour burn rate from the High EPA Test and the BTU content of 
cordwood (8600) times the ef

fi

 ciency.

Содержание 27I-ACC

































Отзывы: