2
7046-191C
April 30, 2015
27I-ACC
5 00
Model: 2700-I ACC
WOOD INSERT
Report:
#061-S-78-6.2
U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to comply with 2015 particulate emission standards at 4.2 G/HR
EPA Method 28 and 5G. Not approved for sale after May 15, 2020. This wood heater needs periodic inspection and repair for
proper operation. Consult the owner’s manual for further information. It is against federal regulations to operate this wood
heater in a manner inconsistent with the operating instructions in the owner’s manual.
2015 2016 2017 Jan Feb Mar Apr May June July Aug Sept Oct. Nov. Dec.
LISTED ROOM HEATER, SOLID FUEL TYPE.
"For Use with Solid Wood Fuel Only."
Also for use in Mobile Home.
DO NOT REMOVE THIS LABEL
7046-153D
Manufactured by:
R
HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING
AWAY. CONTACT MAY CAUSE SKIN BURNS.
CAUTION:
TESTED TO:
UL 1482, ULC S628-93
Install and use only in accordance with manufacturer's installation, venting and operating instructions.
CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA
Refer to manufacturer's instructions and local codes for precautions required for passing chimney through a combustible wall or ceiling.
WARNING - For Mobile Homes: Do not install in a sleeping room. An outside combustion air inlet must be provided and unrestricted
while unit is in use. The structural integrity of the mobile home floor, ceiling and walls must be maintained. The insert must be properly
grounded to the frame of the mobile home. A complete relining of the chimney system with a 6
inch
(152mm) diameter listed stainless
liner is required. Must be equipped with a spark arrestor cap. Outside Air comes standard on the insert and must be installed before
operating insert.
When used as a masonry insert stove, install only in a masonry fireplace built to national and/or local codes. Do not remove brick or
mortar to accommodate insert. Installation requires a 5 foot minimum length of a starter pipe into existing chimney with airtight face seal.
Install only on a non-combustible hearth. Approved for installation and use in factory built zero-clearance fireplaces conforming to
minimum fire chamber specifications.
Components required for installation: positive or direct flue connection assembly or listed vent liner.
In Canada a full length 6
inch
(152mm) S635 flue liner is required as per ULC S628-93.
WARNING - Inspect and clean chimney frequently. Under certain conditions of use, creosote buildup may occur rapidly.
Do not connect this unit to a chimney serving another appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing. Route power cord away from unit. Do not route cord
under or in front of appliance.
Electrical Rating: 115 VAC .63 AMPS 60 Hz
Do not use grate or elevate fire. Build wood fire directly on firebrick. Do not overfire. If heater or chimney connector glows, you are overfiring.
Operate only with doors closed. Open only to add fuel to the fire.
Replace glass only with 5mm ceramic available from your dealer.
PREVENT HOUSE FIRES
No Thermal Floor Protection Required in USA
Ember Floor Protection Required on All Installations
Minimum Clearances To Combustible Material
Masonry, Heat Circulating & Zero Clearance
USA
ONLY
A
Sidewall to Stove
19-3/4 in.
B
Mantel to Stove
21-1/2 in.
C Top Trim to Stove
14 in.
D
Side Trim to Stove
13 in.
E
Hearth Extension from Glass
Floor height 0 in. to 3-1/2 in. below insert base
18 in.
Floor height greater than 3-1/2 in. below insert base 16 in.
F Hearth Extenson from Side of Insert
8 in.
KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIAL FAR AWAY FROM
THE APPLIANCE. SEE NAMEPLATE AND
INSTRUCTIONS.
1445 N. Highway, Colville, WA 99114
www.quadrafire.com
Refer to Clearances on reverse side for Canada
Serial No / Numéro De Série
007013
Mantel
Hearth Extension
A
B
C
F
E
Insert
SideW
all
Maximum Mantel Depth - 10 inches (254mm)
Fascia or Trim
D
O-T L
Tested and
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
Made in U.S.A.
of US and
imported parts.
OWNER’S MANUAL
INSTALLATION MANUAL
A. Congratulations
Hearth & Home Technologies welcomes you to our tradition
of excellence! In choosing a Quadra-Fire appliance, you
have our assurance of commitment to quality, durability, and
performance.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world’s most
advanced technology to achieve the optimum opera-
tion of our stoves, inserts and
fi
replaces. And yet we are
old-fashioned when it comes to craftsmanship. Each unit
is meticulously fabricated and gold and nickel surfaces are
hand-
fi
nished for lasting beauty and enjoyment. Our pledge
to quality is completed as each model undergoes a quality
control inspection.
We wish you and your family many years of enjoyment in
the warmth and comfort of your hearth appliance. Thank
you for choosing Quadra-Fire.
B. Sample of Serial Number / Safety Label
LOCATION: UNDER INSERT RIGHT SIDE PANEL - SWIVEL OUT TO VIEW
NOTE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction
SAMPLE
Test Lab & Report
Number
Mfg Date
Serial Number
Model Name
and Welcome to the Quadra-Fire Family
!
