Quadra-Fire 2100-I Скачать руководство пользователя страница 7

Страница: 7 / 28

2100-I & 3100-I FIREPLACE INSERT

Page 7

March 1999

MANUFACTURED BY:

Approved for installation and use in factory built zero-

clearance fireplaces conforming to minimum fire

chamber specifications.

Components required for installation: positive or direct

flue connection assembly or listed vent liner. Inspect

and clean vent system frequently in accordance with

manufacturers instructions.

In Canada a full length S635 flue liner is required.

For use with solid wood fuel only. Do not use grate or

elevate fire. Build wood fire directly on hearth.

Route power cord away from unit. Do not route cord

over or under appliance.

DANGER: Risk of electrical shock. Disconnect power

supply before servicing.

Optional component:

Blower Assembly: Part #831-1101

Electrical Rating:

115 VAC, .6 Amps, 60 Hz.

123456789012345678901234567890121234567890123456789012345678901

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with July 1990 particulate emissions standards.

Date of Manufacture

1999 2000 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec.

SAFETY LABELS

Listed solid fuel heater for installation in masonry or fac-

tory bult fireplaces.

LISTED TO: UL 1482, ULC S628

TYPE OF FUEL: SOLID WOOD ONLY

PREVENT HOUSE FIRES

Install and use only in accordance with manufacturers

installation, venting and operating instructions. Do not

remove bricks or mortar from masonry fireplace. Install

only on a non-combustible hearth. Contact local build-

ing or fire officials about restrictions and installation in-

spections in your area.

Do not connect this unit to a chimney serving another

appliance.

When used as a masonry insert stove, install only in a

masonry fireplace built to UBC Chapter 37. Do not re-

move brick or mortar to accommodate insert. Installa-

tion requires minimum of a starter pipe into existing chim-

ney with airtight face seal.

CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND

INSTALLATION INSPECTION IN YOUR AREA

HEARTH EXTENSION

MANTEL

INSERT

INSTALLATION

UNITED STATES

CANADA

815mm 685mm 355mm 305mm 405mm 200mm

Minimum Clearances to Combus-

tible Materials (in inches)

Install insert with a mimimum of

32 clearance to combustible

sidewall, 10 to side and 14 to top

trim, 22 from top of insert to man-

tel. Floor protector must be 3/8

mimimum non-combustible mate-

rial or equivalent, extending 16 in

front and 8 to both sides.

Model:

Serial No.

QUADRA-FIRE

3100-I

Operate only with doors closed. Replace glass only with

5mm ceramic available from your dealer.

Содержание 2100-I





























Результаты поиска

Содержание 2100-I

Отзывы:

Похожие инструкции для 2100-I

Бренды по названию

Популярные бренды

Quadra-Fire 2100-I, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 2100-I

Отзывы:

Похожие инструкции для 2100-I

Бренды по названию

Популярные бренды