Quadra-Fire 2100-I Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 28

background image

2100-I & 3100-I FIREPLACE INSERT

Page 13

March 1999

INSTALLATION OF PANEL SET

Materials needed: Phillips Screwdriver and double sided tape or contact adhesive.

1. Remove four 1/4 - 20 screws from nuts attached to insert outer wall.

2. Slide side panels in front on insert outer wall, align horizontal and

vertical slots and install 1/4 - 20 screws (do not tighten).

3. Remove two 1/4 - 20 screws from top panel.

4. Attach top panel by means of two clips welded on the back side of panel.

5. Insert two 1/4 - 20 screws through holes in outer edges of side panels

into nuts welded inside top panel. Tighten.

6. Center the panels and tighten screws holding side panels.

7. Install screen covers.

8. Attach insulation strip to the outside edge of the backside of top and side

panels. Use double sided tape or a contact adhesive to hold insulation in

place.

INSTALLATION OF FACE TRIM PACKAGE

(For use with part # 831-1150, Black Side Screens Only)

(TOP VIEW)

INSTALLATION OF DOOR HANDLE

DOOR HANDLE ASSEMBLY

SPRING HANDLE

DOOR HANDLE

KEY DOOR

LATCH CAM

NUT

WASHERS

NOTE: SPRING HANDLE IS NOT

INCLUDED IN ASSEMBLY. MUST

BE ORDERED SEPARATELY.

SPRING HANDLE ORDER #832-0620

INST

ALLA

TION:

P

ANEL, TRIM &

DOOR HANDLE

PANEL

FIREBOX

FACE

FAN

Press fit the trim between

face and decorative screen.

«
...
11
12
13
14
15
...
»

Содержание 2100-I





























Отзывы:

Нет отзывов

Похожие инструкции для 2100-I

Бренд: Valor Fires Страницы: 49

Бренд: Majestic fireplaces Страницы: 28

Бренд: Majestic fireplaces Страницы: 52

Бренд: Majestic fireplaces Страницы: 4

Бренд: Majestic fireplaces Страницы: 24

Бренд: Majestic Страницы: 64

Royal Collection WMC36

Бренд: Majestic fireplaces Страницы: 8

PerfectView 33LDV

Бренд: Majestic fireplaces Страницы: 4

Бренд: Majestic Страницы: 48

Бренд: GRAND EFFECTS Страницы: 28

Бренд: Varde Страницы: 44

Бренд: Uniflame Страницы: 2

Бренд: Scott Living Страницы: 27

Бренд: Empire Comfort Systems Страницы: 28

PONDEROSA LS-24P-1

Бренд: White Mountain Hearth Страницы: 12

Бренд: FBR Страницы: 30

Бренд: BRW Страницы: 2

Бренд: Napoleon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды