background image

 

 

 

Page | 20 

 

lack of reasonable and proper maintenance, failure to follow operating instructions, 
misuse, lack of proper protection during storage, or accident, (7) Normal maintenance 
parts, lubricants, and service, (8) Exposure of Product to non-approved contents and 
environments, including, but not limited to, fuel, chemical agents, industrial effluents, 
and extreme temperatures.      

SECURING WARRANTY SERVICE

 – To secure warranty service, Purchaser must (1) 

Report Product defect to MTECH and request repair within the applicable warranty 
term, (2) Present evidence of the warranty start date, and (3) Make Product available to 
MTECH within a reasonable period of time as agreed upon with MTECH.  

LIMITATION OF IMPLIED WARRANTIES AND OTHER REMEDIES

 – To the extent 

permitted by law, neither MTECH nor any company affiliated with it makes any 
warranties, representations or promises as to the quality, performance or freedom from  

defect of Product covered by this warranty. IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO THE  
EXTENT APPLICABLE, SHALL BE LIMITED IN DURATION TO THE APPLICABLE  
PERIOD OF WARRANTY SET FORTH IN THIS SECTION. PURCHASER’S ONLY  
REMEDIES IN CONNECTION WITH THE BREACH OR PERFORMANCE OF ANY  
WARRANTY ON THE PRODUCT ARE THOSE SET FORTH ON THIS PAGE. IN NO  
EVENT WILL MTECH OR ANY COMPANY AFFILIATED WITH MTECH BE LIABLE 

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. (Note: Some states do not allow 
limitations on how long an implied warranty lasts or the exclusion or limitation of 
incidental or consequential damages so the above limitations and exclusions may not 
apply to you.) This warranty gives you specific legal rights, and you may also have other 
rights which vary from state to state. 

Содержание 70HPK





















Отзывы: