background image

25

Maintenance, Warranty & QSC Contact Information

Cleaning

The faceplate and chassis can be cleaned with a soft cloth and

nonabrasive, mild  cleaning solution. Products like Simple Green

and Windex work well. Do not use powders or scrubbing pads of any

type as they are usually abrasive and will permanently damage the

finish of your DSP-30.  Dampen a soft, lint-free cloth with the

cleaning solution and wipe the unit down gently. Insure that

cleaning solution does not get into the connectors. Do not spray the

solution directly onto the unit as it will penetrate into the connec-

tors.

User Maintenance

There are no user servicable parts in the DSP-30. Contact QSC’s

Technical Services Department if service is required.

Warranty Information

If the DSP-30 isn’t working properly, please verify that a known

good 9-pin serial cable is used between the DSP-30 and the

computer for loading Presets. If proper operation can not be

restored, the DSP-30 may require service. This must be per-

formed by qualified service personnel. To obtain the location of

your nearest QSC Authorized Service Center, please contact your

QSC dealer or contact QSC’s Technical Services Department.

WORLD WIDE WEB:

http://www.qscaudio.com

FACSIMILE (FAX) NUMBERS:

Sales & Marketing FAX

(714) 754-6174

Technical Services FAX

(714) 754-6173

TELEPHONE NUMBERS:

Main Number

(714) 754-6175

Sales Direct Line (714) 957-7100

or  (800) 854-4079 toll free (U.S.A. only)

Technical Services (714) 957-7150

 or (800) 772-2834 toll free (U.S.A. only)

ADDRESS:

QSC Audio Products, Inc.

1675 MacArthur Boulevard

Costa Mesa, CA 92626-1468  USA

Disclaimer

QSC Audio Products, Inc. is not liable for any damage to speakers,

amplifiers, or any other equipment that is caused by negligence or

improper installation and/or use of this digital signal processor.

QSC Audio Products, Inc. is not liable for any direct or indirect

damage caused by computer communications failure.

Product Warranty

QSC guarantees the DSP-30 to be free from defective material and/

or workmanship for a period of three years from the date of sale, and

will replace defective parts and repair malfunctioning products

under this warranty when the defect occurs under normal installa-

tion and use—provided the unit is returned to our factory via

prepaid transportation with a copy of the proof of purchase, such as

a sales receipt. This warranty provides that examination of the

returned product must indicate, in our judgment, a manufacturing

defect. This warranty does not extend to any product which has

been subjected to misuse, neglect, accident, improper installation,

or where the serial number and date code have been removed or

defaced.

If the DSP-30 is returned to the factory for service, it should be sent

in the proper QSC carton. If you did not save the original carton, ask

your QSC dealer for one or call QSC to have one sent to you. This

warranty does not cover shipping damage caused by improper

packing or  the use of improper shipping cartons.

Содержание DSP-30





























Отзывы: