QNAP TS-1270U-RP Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 83

background image

24

Chapter 4.

LED and Alarm Buzzer Specifications

The LED indicators of the NAS indicate the system status and information. When the NAS
is turned on, check the following items to make sure the system status is normal. Note
that the following LED information is applicable only when users have properly installed the
hard drive, and connected the NAS to the network and the power supply.

LED

Color

LED Status

Description

System

Status

Red/

Green

Flashes green

and red

alternately

every 0.5 sec

1.

The hard drive on the NAS is being
formatted.

2.

The NAS is being initialized.

3.

The system firmware is being updated.

4.

RAID rebuilding is in process.

5.

Online RAID Capacity Expansion is in
process.

6.

Online RAID Level Migration is in process.

Red

1.

The hard drive is invalid.

2.

The disk volume has reached its full
capacity.

3.

The disk volume is going to be full.

4.

The system fan is out of function.

5.

An error occurs when accessing
(read/write) the disk data.

6.

A bad sector is detected on the hard
drive.

7.

The NAS is in degraded read-only mode
(2 member drives fail in a RAID 5 or RAID
6 configuration, the disk data can still be
read).

8.

Hardware self-test error.

Flashes red

every 0.5 sec

The NAS is in degraded mode (one member
drive fails in RAID 1, RAID 5 or RAID 6
configuration).

Flashes green

every 0.5 sec

1.

The NAS is starting up.

2.

The NAS is not configured.

3.

A hard disk drive is not formatted.

Green

The NAS is ready.

Off

All the hard disk drives on the NAS are in
standby mode.

LAN

Orange

Orange

The disk data is being accessed from the
network and a read/write error occurs during
the process.

«
...
22
23
24
25
26
...
»

Содержание TS-1270U-RP




















































































Отзывы:

Нет отзывов

Похожие инструкции для TS-1270U-RP

Бренд: iDirect Страницы: 60

Бренд: National Instruments Страницы: 11

Бренд: Queclink Страницы: 9

Optane M Series

Бренд: Intel Страницы: 59

Бренд: DAD Страницы: 32

Бренд: Maxim Страницы: 14

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

Бренд: Asante Страницы: 150

Бренд: Giacomini Страницы: 2

Vocal Performer VE-20

Бренд: Boss Страницы: 20

Бренд: National Instruments Страницы: 80

Бренд: Advantech Страницы: 108

Бренд: ADTRAN Страницы: 20

Бренд: JLCooper Electronics Страницы: 12

Бренд: ICS ELECTRONICS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды